Display.elements; Changing.the.menu.options - Trotec TA 300 Manual De Instrucciones

Press. (setup). to. switch. the. background. lighting.
on . . Press.the.button.again.to.switch.it.off.again .
Press. and. hold. the.
3.seconds.to.access.the.menu.(see.also.„Changing.
menu.options.and.settings") . . Press.and.hold.the.
(Setup).button.again.for.approx . . 3.sec.to.exit.from.the.
menu . . Press. .(Enter).while.you.are.in.the.menu:.
Activate.the.option.that.you.wish.to.change.by.pres-
sing. the. . (Enter). button. and. then. press. the.
(Enter).button.again.to.save.the.changes.you.have.made .
Press.Unit. / .to.change.the.units.of.measurement . .
Press.Unit. .to.display.the.speed.in.m/s.or.in.km/h.
or. in. ft/min. or. in. mph. or. in. knots;. Press. Unit. . to.
change.the.temperature.scale.from.°C.to.°F.or,.if.you.
are.in.flow.(volumetric.flow).mode,.to.change.the.unit.
from.ft³/min.(CFM).to.m³/min.(CMM) .
If.you.are.in.the.menu.and.have.placed.the.option.in.
the.change.state.with.the.
increase.the.number.(0.-.9).with.Unit. .and.decrease.
the.number.(0.-.9).with.Unit. .
Press. .(Max/Min).to.freeze.the.maximum.or.mini-
mum.measured.value.and.hold.this.button.for.approx . .
2.seconds.to.return.to.normal.mode . . Press. .(Mean).
to.perform.a.multi-point.mean.value.calculation.or.a.
mean. value. calculation. over. time . . Press.
Temp).to.switch.between.temperature,.air.speed.and.
the.calculated.volumetric.air.flow .
.
04. Display elements
1).„Low.battery".symbol
2).Primary.display.air.speed
3).Air.speed.units.(m/s,.km/h,.ft/min,.mph,.knots)
B - 3
. (Setup). button. for. approx . .
.(Enter).button,.you.can.
. (Flow/
OPERATING MANUAL – HOT-WIRE ANEMOMETER TA300
. 4). T emperature,. volumetric. flow. rate:. temperature. .
.... .units.(°C/°F),.volumetric.flow.rate.units.(CFM.-.ft³/. .
..... min,.CMM.-.m³/min)
. 5).Secondary.display
. 6).Max/Min.display
. . . .
. 7). S ymbol.for.multi-point.mean.value.calculation
. 8).Mean.value.calculation
. 9). S ymbol.for.mean.value.calculation.over.time
.
10).A.multiple.of.the.secondary.display.data
11).Volumetric.flow.rate.units
12).Temperature.units
13).Area.units.for.flow.cross-section
14).A.multiple.of.the.secondary.display.data
15).Symbol.for.automatic.power-off
16).Symbol.for.the.time
17).Hold.function
18).Access.the.menu,.exit.from.the.menu
05. Changing the menu options
The.menu.can.be.used.to.change.the.units.for.the.vo-
lumetric.flow,.the.cross-section.of.the.flow.duct.and.
the.settings.for.the.automatic.power-off .
Accessing the menu / exiting from the menu
Press.and.hold.the.
sec . . to.access.the.menu . . The.word.„SETUP".appears.
on. the. display. once. you. have. accessed. the. menu . .
Press.and.hold.the.
sec.to.exit.from.the.menu .
Menu options
Options Menu.item
Change.the.unit. Unit
for.the.assumed.
cross-section.of.
the.flow.duct
.(Setup).button.for.approx . . 3.
.(Setup).button.for.approx . . 3.
Setting
Select.unit.(in²,.
m²,.ft²)