Part Description; Safety Precautions - Dolmar LT-CS Instrucciones De Manejo

Part description (Fig. 1)
The numbers below refer to the figure
1. Shaft
2. Protector (Guard)
3. Cord cutter
4. Nylon cutting head

Safety precautions

WARNING: Read all safety warnings and all instructions
in this booklet and the instruction manual of the power unit.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "string trimmer" and "equipment" in the warnings and
precautions refer to the combination of the attachment and the
power unit.
Intended use
• This attachment is designed only for the purpose of trimming
grass and light weed in conjunction with an approved power unit.
Never use the attachment for the other purpose. Abusing the
attachment may cause serious injury.
General precautions
• Before starting the string trimmer, read this booklet and the
instruction manual of the power unit to become familiar with the
handling of the string trimmer.
• Do not lend the attachment to a person with insufficient
experience or knowledge regarding handling of string trimmers.
• When lending the attachment, always attach this instruction
manual.
• Do not allow children or young persons under 18 years old to use
the string trimmer. Keep them away from the string trimmer.
• Handle the string trimmer with the utmost care and attention.
• Never use the string trimmer after consuming alcohol or drugs, or
if feeling tired or ill.
• Never attempt to modify the attachment.
• Follow the regulations about handling of string trimmers in your
country.
Personal protective equipment
• Wear safety helmet, protective goggles and protective gloves to
protect yourself from flying debris or falling objects. (Fig. 2)
• Wear ear protection such as ear muffs to prevent hearing loss.
• Wear proper clothing and shoes for safe operation, such as
a work overall and sturdy, non-slip shoes. Do not wear loose
clothing or jewelry. Loose clothes, jewelry or long hair can be
caught in moving parts.
Work area safety
• Operate the equipment under good visibility and daylight
conditions only. Do not operate the equipment in darkness or fog.
• Start and operate the engine only outdoors in a well ventilated
area. Operation in a confined or poorly ventilated area can result
in death due to suffocation or carbon monoxide poisoning.
• During operation, never stand on an unstable or slippery surface
or a steep slope. During the cold season, beware of ice and snow
and always ensure secure footing.
• During operation, keep bystanders or animals at least 15 m
away from the equipment. Stop the engine as soon as someone
approaches.
• Before operation, examine the work area for stones or other
solid objects. They can be thrown and cause injury or property
damage.
• WARNING: Use of this product can create dust containing
chemicals which may cause respiratory or other illnesses.
Some examples of these chemicals are compounds found in
pesticides, insecticides, fertilizers and herbicides.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals, work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
Putting into operation
• Before assembling or adjusting the equipment, switch off the
engine and remove the spark plug.
• Before starting the engine, inspect the equipment for damages,
loose screws/nuts or improper assembly. Check all control levers
and switches for easy action. Clean and dry the handles.
• Never attempt to start the engine if the equipment is damaged or
not fully assembled. Otherwise serious injury may result.
• Adjust the shoulder harness and hand grip to suit the operator's
body size.
Starting engine
• Wear the personal protective equipments before starting the
engine.
• Start the engine at least 3 meters (10 feet) away from the fueling
spot.
• Before starting the engine, make sure that there is no person or
animal in the work area.
• When starting the engine, keep the rotating parts clear of your
body and other object, including the ground. They may rotate
when starting and may cause injury or damage to the equipment
and/or property.
• Place the equipment on firm ground. Maintain good balance and
secure footing.
• When pulling the starter knob, hold the power unit firmly against
the ground by your left hand. Never step on the drive shaft of the
power unit. (Fig. 3)
• Follow the instruction manual of the power unit for starting the
engine.
• If the nylon cutting head rotates at idle, stop the engine and
adjust the idle speed down.
Operation
• In the event of an emergency, switch off the engine immediately.
• If you feel any unusual condition (e.g. noise, vibration) during
operation, switch off the engine. Do not use the equipment until
the cause is recognized and solved.
• The cutting attachment continues to move for a short period after
releasing the throttle trigger or switch off the engine. Don't rush to
contact it.
• With the engine running only at idle, attach the shoulder harness.
• During operation, use the shoulder harness. Keep the equipment
on your right side firmly. (Fig. 4)
• Hold the front handle with the left hand and the rear grip with the
right hand, no matter you are right-hander or left-hander. Wrap
your fingers and thumbs around the handles.
• Never attempt to operate the equipment with one hand. Loss
of control may result in serious or fatal injury. To reduce the
risk of injury, keep your hands and feet away from the cutting
attachment.
• Do not overreach. Keep proper footing and balance at all times.
Watch for hidden obstacles such as tree stumps, roots and
ditches to avoid stumbling.
• If the equipment gets heavy impact or fall, check the condition
before continuing work. Check the fuel system for fuel leakage
and the controls and safety devices for malfunction. If there is
any damage or doubt, ask Dolmar authorized service center for
the inspection and repair.
• Take a rest to prevent loss of control caused by fatigue. We
recommend to take a 10 to 20-minute rest every hour.
• When you leave the equipment, even if it is a short time, always
switch off the engine. The equipment unattended with the engine
running may be used by unauthorized person and cause serious
accident.
• Follow the instruction manual of the power unit for proper use of
the control lever and switch.
• During or after operation, do not put the hot equipment onto dry
grass or combustible materials.
• Never attach cutting blades. Blade contact may result in serious
injury.
• Never touch or approach the cutting attachment while it is
moving. When handling the cutting attachment, stop the engine
and remove the spark plug cap.
• Check the cutting attachment frequently during operation for
cracks or damages. Before the inspection, switch off the engine
5