Virutex CE35E Manual De Instrucciones página 6

1. Before starting up the machine make sure that the supply
voltage is the same as that shown on the specification plate.
2. Always keep hands clear of the cutting area, and always
hold the machine using the grips.
3. Always use original VIRUTEX blades. Never use blunt
or damaged blades or blades of the wrong size or in poor
condition.
Always use the original VIRUTEX blade holders and blade
supports mounted on the machine. If necessary, replace
them with original VIRUTEX parts.
4. It is necessary to work with dust collection in order to
prolong the life of the blades and prevent any breakages.
5. Avoid cutting nails. Check the work surface before planing.
6. Wait until the machine has come to a complete stop
before putting it down or storing it.
7. Wear earplugs when using the machine (see chapter 10)
2. TECHNICAL CHARACTERISTICS
Imput Power....................................................................700 W
Motor..............................................................................50/60 Hz
No load speed.........................................................16,500 /min
Cuts per minute...................................................................33,000
Cutting width......................................................................80 mm
Cutting depth.............................................................0-3 mm
Rabbeting depth......................................................11 mm
Weight........................................................................3.2 kg
Weighted equivalent continuous
acoustic pressure level A................................................87 dBA
Acoustic power level A....................................................98 dBA
Uncertainty..................................................................K = 3 dbA
Wear ear protection!
Vibration total values.............................................a
Uncertainty.................................................................K: 1.5 m/s
3. STANDARD EQUIPMENT
Contained in the transportation case you will find the
following elements:
1. Planer CE35E
2. Guide stop
3. Dust collector connection
4. Key for securing the blades
4. GENERAL DESCRIPTION
The CE35E planer is equipped with replaceable, twin-use
blades of hard metal, side shoes for giving depth on recesses
or gains M (Fig. 2), a guide stop for working from references
or from the side, and a safety switch with inverse locking,
which prevents accidental start up of the machine.
The machine is equipped with a dust collector connec-
tion which can be used for connection to our AS182K,
AS282K dust collector or any industrial equivalent via the
STANDARD DUST COLLECTOR ATTACHMENT (ref. 6446073).
For assembling the dust collector connection, remove the
chips outlet guide A (Fig. 1) using screws B and fit the dust
collector connection in its place.
6
5. REGULATING THE CUT
Turn knob C (Fig. 2) until the required depth is reached
(Maximum depth of cut 3 mm).
6. REPLACING THE BLADES
Changing and regulating the blades
Release screws D (Fig. 3) and slide the blade sideways until
it comes out of the blade-holder cartridge. Insert the new
blade and tighten screws D.
The machine's blade-holders are accurately adjusted and do
not normally require any further adjustment. If, however,
this becomes necessary, this is done by adjusting screws F
until the blades are parallel to the machine base using a
rule supported on the base. The blades supplied by Virutex
are reversible (double-edge).
For blade-holder system spares use only original VIRUTEX
components.
7. CHANGING THE TRANSMISSION BELT
Unscrew screws H (Fig. 4) and remove protection G. Replace
the worn belt with a VIRUTEX original spare, taking care to
fit it correctly into the pulley cogs, never forcing it.
: <2.5 m/s
2
h
2
8. MAINTENANCE OF THE BRUSHES AND COLLECTOR
The brushes must be replaced when they reach a minimum
length of 5 mm (Fig. 5)
Unscrew the black caps E (Fig. 2) on the housing and remove
the brushes from the guide. Replace them with new Virutex
original spares, ensuring that they move smoothly inside the
guides. Screw on the cap which covers them and leave the
machine running for 15 minutes. If the collector is burned
or uneven it should be repaired by a Virutex service agent.
Always keep the lead and plug in good working condition.
9. ACCESSORIES
3540118 - Set of reversible straight MD blades CE24E/CE35E
(Included with equipment)
3531019 - Set of reversible straight AR blades CE24E/CE35E
3599101 - Set of standard blades
Disconnect the machine from the mains
before carrying out this operation.
Ensure that screws D are correctly tightened
before resuming work with the machine.
Disconnect from the mains before carrying
out any maintenance operations.