Additional Safety Rules - Makita 4093D Manual De Instrucciones

ENGLISH
1 Rear cover
2 Switch
3 Nozzle
4 Cleaner body
5 Extension wand (Straight pipe)
SPECIFICATIONS
Model
Capacity ................................................................500 ml
Continuous use
(with battery 9000) .........................High: Approx. 13 min.
Overall length ......................................................484 mm
Net weight ..............................................................1.3 kg
Rated voltage ...................................................D.C. 9.6 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for collecting dry dust.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
7. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
4
Explanation of general view
6 Corner nozzle
7 Front cover
8 Depress
9 Open
10 Dust bag
4093D
Low: Approx. 23 min.
ENC004-1
11 Hook front cover onto front lip
12 Close
13 Front lip
9. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.

ADDITIONAL SAFETY RULES

1. Read this instruction manual and the charger
instruction manual carafully before use.
2. Do not pick up wet materials, lit cigarettes or the
like.
3. Stop operation immediately if you notice any-
thing abnormal.
4. If you drop or strike the cleaner, check it care-
fully for cracks or damage before operation.
5. Do not bring close to stoves or other heat
sources.
6. Do not block the intake hole or vent holes.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the cleaner before insertion or
removal of the battery cartridge.
• To remove the battery cartridge, remove the rear cover
from the cleaner by pushing it in the direction of the
arrow and then withdraw the battery cartridge from the
cleaner.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the cleaner and slip
it into place. Then close the rear cover.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.