Battery Charging - Bosch GOP 12V-LI Professional Manual Original

OBJ_BUCH-2923-001.book Page 16 Monday, July 25, 2016 3:37 PM
16 | English
Assembly

Battery Charging

 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
Removing the battery
To remove the battery 2, press the unlocking buttons 1 and
pull the battery out of the machine to the rear. Do not exert
any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
4 indicate the charge condition of the battery 2. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
To indicate the charge condition, press and hold button 3 of
the switched off machine.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Changing the Tool
 Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 Wear protective gloves when changing application
tools/accessories. Contact with the application tool/
accessory can lead to injuries.
Selecting the Application Tool/Accessory
Accessory
HCS wood seg-
ment saw blade*
BIM segment saw
blade*
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
1 609 92A 30J | (25.7.16)
Accessory
Capacity
2/3
1/3
<1/3
Reserve
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/ac-
cessory.
For removing the application tool/accessory, loosen the
screw 11 with the hex key 12 and remove the application
tool/accessory.
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 10) in such a manner on the tool holder 8 that
Material
the offset faces downward (see illustration on the graphics
Wooden materials,
page; marking on the application tool/accessory is readable
plastic
from above).
Wooden materials,
Turn the application tool/accessory to a position favourable
plastic, non-ferrous
for the respective job, and allow it to engage into the cams of
metals
the tool holder 8. 12 different positions are possible, each
offset by 30°.
For more intermediate positions, the adapter 13 (accessory)
can be used: Allow the adapter to engage with the smooth
side onto the cams of the tool holder 8 (see illustration on the
graphics page). Position the application tool/accessory onto
the adapter in any position.
Material
HCS plunge cut Wooden materials,
saw blades, plastic, gypsum
wood* and other soft
materials
BIM plunge cut Metal (e. g. unhard-
saw blades, ened nails, screws,
metal* smaller profiles),
non-ferrous metals
BIM plunge cut Wood, metal, non-
saw blade, wood ferrous metals
and metal*
HM-Riff segment Grouting joints,
saw blade* soft wall tiles,
glass-fibre rein-
forces plastic and
HM-Riff delta
other abrasive
plate*
materials
Scraper, rigid* Carpets, coverings
Scraper, flexible* Silicone and other
elastic materials
Base plate for Depends on
sanding, series sanding sheet
Delta 93 mm*
Bosch Power Tools