Tensioning The Chain - Craftsman PRO Serie Manual Del Operador

GENERAL SAFETY PRECAUTIONS
General advice on adjusting depth gauge setting
When you sharpen the cutting tooth (A) the depth
gauge setting (C) will decrease.To maintain optimal
cutting performance the depth gauge (B) has to be
filed down to achieve the recommended depth gauge
setting. See instructions under the heading Technical
data to find the correct depth gauge setting for your
particular chain.
too large[
Adjustment of depth gauge setting
The cutting teeth should be newly sharpened before
adjusting the depth gauge setting. We recommend
that you adjust the depth gauge setting every third
time you sharpen the cutting teeth. NOTE[ This
recommendation assumes that the length of the
cutting teeth is not reduced excessively.
You will need a flat file and a depth gauge tool. We
recommend that you use our depth gauge tool to
ache|re the correct depth gauge setting and bevel for
the depth gauge.
Place the depth gauge tool over the chain. Detailed
information regarding the use of the depth gauge tool,
will be found on the package for the depth gauge tool.
Use the flat file to file off the tip of the depth gauge that
protrudes through the depth gauge tool. The depth
gauge setting is correct when you no longer feel
resistance as you draw the file along the depth gauge
tool.
Tensioning the chain
__haio may jumpoff. |
| / _rio.o o,even f atal |
i,,,,,,,,,,,,,,_ mjury.
_lways_wear approved. !
| "="""""'_ chain c_ous cuts to yourself |
or personsyou bump into with an |
exposed chain.
The more you use a chain the longer it becomes. It is
therefore important to adjust the chain regularly to take up
the slack.
Check the chain tension every time you refuel. NOTE! A
new chain has a running-in period during which you
should check the tension more frequently.
Tension the chain as tightly as possible, but not so tight
that you cannot pull it round freely by hand. (11)
Switch the engine off. (29)
Undo the bar nut that hold the clutch cover/chain
brake. Use the combi-tool integrated in the rear
handguard or one with corresponding dimensions
(contact your servicing dealer (retailer) for a
replacement tool).Then tighten the bar nut by hand as
tight as you can. (12)
Raise the tip of the bar and stretch the chain by
tightening the chain tensioning screw using the comb|-
tool. Tighten the chain until it does not sag from the
underside of the bar. (13)
Use the combi-tool to tighten the bar nut while lifting
the tip of the bar at the same time. Check that you can
pull the chain round freely by hand and that it does not
sag from the underside of the bar. (14) (15)
Lubricating cutting equipment
_at+on.of.cutt+ng |
| / _se the chain to snap, |
|
fatal |
injuries.
Chain oil
Chain oil must demonstrate good adhesion to the chain
and also maintain its flow characteristics regardless of
whether it is warm summer or cold winter weather.
Never use waste oiH Using waste oil can be dangerous
to you and damage the machine and environment.
IMPORTANT! When using vegetable based saw chain
oil, dismantle and clean the groove in the bar and saw
chain before long-term storage. Otherwise there is a risk
of the saw chain oil oxidizing, which will result in the saw
chain becoming stiff and the bar tip sprocket jamming.
Filling with chain oil
All our chain saws have an automatic chain lubrication
system. On some models the oil flow is also
adjustable.
The saw chain oil tank and the fuel tank are designed
so that the fuel runs out before the saw chain oil.
However, this safety feature requires that you use the
right sort of chain oil (if the oil is too thin it will run out
before the fuel), and that you adjust the carburetor as
recommended (a lean mixture may mean that the fuel
lasts longer than the oil) and that you also use the
recommended cutting equipment (a bar that is too
long will use more chain oil).
Checking chain lubrication
Check the chain lubrication each time you refuel. See
instructions under the heading Lubricating the bar tip
sprocket.
Aim the tip of the bar at a light coloured surface about
20 cm (8 inches) away. After 1 minute running at 3/4
throttle you should see a distinct line of oil on the light
surface.
If the chain lubrication is not working:
Check that the oil channel in the bar is not obstructed.
Clean if necessary.
English - 15