AmpPanel&Controls; Volume Control - Monitor Audio BRONZE W10 Manual Del Propietário

Ocultar thumbs Ver también para BRONZE W10:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 35
AmpPanel&Controls
INPUT
2
LFE
R
1
L
1. RCA Stereo Inputs (Left & Right)
This is the method of signal input when using a stereo amplifier system, connection can be provided by a pair of
high-quality signal cables from the pre-out section of an amplifier. The crossover frequency will need to be set
if using this method of connection. If using the Bronze Series speakers set the crossover dial to approximately
80Hz. This may vary depending on room and tastes.
Note:- cable lengths should not exceed 10 metres to avoid interference from other electrical appliances.
2. LFE Input (RCA Type)
This input is to be used when connecting the subwoofer to an AV amplifier/ receiver. When using the LFE input, the crossover
frequency dial is not used. This is due to the crossover function being controlled by the AV amplifier/ processor
to which it is connected.
3. 12 Volt Trigger Input ~ Centre Pin = +12Vdc
For external power control from AV amplifier/ receiver to the Bronze W10. Monitor Audio recommend using this
function and a lead is supplied. A 12 volt signal is supplied by the AV amp/receiver and tells the Bronze W10 to
turn on from standby mode. This allows a more accurately controlled auto on/off function, and is far more energy
efficient. When using the 12v trigger, the Mode Switch (8) can be in either position, for it to function correctly.
4. Crossover Frequency Control
The crossover frequency control only operates when using the RCA stereo input (1) and is used to set the upper
frequency limit (low pass) of the subwoofer. The crossover control should be set in accordance with the size or
bass output of the main/satellite speakers. When using the Bronze Series speakers, set this to between 50 - 100Hz
(depending on additional speakers). Experimentation is advisable.

5. Volume Control

This control allows the level or volume to be adjusted in order to achieve a balanced overall sound. To get the
balanced sound a selection of familiar music or film excerpts will need to be played. Start with the volume at
minimum and increase the level control until a balanced sound is established.
2
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
ATTENTION: AFIN DE RÉDUIRE TOUT RISQUE DE CHOC
ÉLECTRIQUE, NE PAS RETIRER LE COUVERCLE
(OU CAPOT ARRIERE), NE CONTIENT PAS DE PIECES
REPARABLES PAR L'UTILISATEUR CONFIER TOUT
ENTRETIEN À UN PERSONNEL QUALIFIÉ.
3
4
TRIGGER
FREQUENCY
.
.
12V
.
50 Hz
120 Hz MIN
220 - 240V~
110 - 120V~
POWER
5
6
BASS
VOLUME
IMPACT
.
.
.
.
.
.
MOVIE
.
.
.
MAX
ON
OFF
Bronze W10
7
8
PHASE
MODE
AUTO
MUSIC
ON
DESIGNED IN THE UK, MADE IN CHINA
Notes:
1. ICONS/TEXT TO BE SILKSCREENED
IN WHITE - RAL 9003
2. IMAGE FOR REFERENCE PURPOSES ONLY.
3. DO NOT SILK SCREEN TEXT
FOR REGERENCE PURPOSES ONLY.
9
10
AC110-120V ~ 50-60Hz
AC220-240V ~ 50-60Hz
200 W
FUSE: 110-120VAC T4AL/250VAC
FUSE: 220-240VAC T4AL/250VAC
10a
11
IN RED
-

Publicidad

Tabla de contenido
loading

Tabla de contenido