EINHELL TC-BJ 900 Manual De Instrucciones página 17

circumstances.
f) Wear suitable work clothes. Do not wear
loose clothing or jewellery. Keep hair, clo-
thes and gloves away from moving parts.
Loose clothing, jewellery or long hair can get
trapped in moving parts.
g) If vacuuming devices and draining de-
vices can be fi tted, make sure that these
are correctly attached and correctly used.
The use of a dust extraction system can redu-
ce the danger posed by dust.
4. Usage and treatment of the electric tool
a) Do not overload the appliance. Use the
correct tool for your work. You will be able
to work better and more safely within the gi-
ven performance boundaries.
b) Do not use an electric tool with a defec-
tive switch. An electric tool that cannot be
switched on or off is dangerous and must be
repaired.
c) Pull the plug out of the socket and/or
remove the battery before making any ad-
justments to the appliance, changing ac-
cessories or put the appliance down. This
safety measure prevents starting the electric
tool unintentionally.
d) Keep unused electric tools out of the
reach of children. Do not allow people
who are not familiar with the appliance or
who have not read these instructions to
use the appliance. Electric tools are dange-
rous if they are used by inexperienced people.
e) Clean your electric tool carefully. Check
whether moving parts are functioning
properly and not jamming, whether parts
are broken or damaged enough that the
functioning of this electric tool is aff ec-
ted. Damaged parts must be repaired be-
fore using the appliance. Many accidents
are caused by badly maintained electric tools.
f) Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
g) Make sure to use electric tools, accesso-
ries, spare parts, etc. in accordance with
these instructions. Take the conditions
in your work area and the job to perform
into account. Using electric tools for any
purpose other than the one for which they are
intended can lead to dangerous situations.
Anl_SA_TC_BJ_900_SPK8.indb 17 Anl_SA_TC_BJ_900_SPK8.indb 17
GB
5. Service
a) Have your electric tool repaired only by
trained personnel and/or the authorized
service agent, using only genuine spare
parts. This will ensure that your electric tool
remains safe to use.
Special safety instructions
Danger!
•
Should the power cable become damaged
during work, do not touch it. Pull out the po-
wer plug immediately. Any damaged power
cables on the electric tool must be replaced
either by the manufacturer or a service com-
pany authorized by the manufacturer.
•
Check that the speed shown on the diamond
cutting wheels is the same or higher than the
rated speed for the masonry channel cutter.
•
Check that the diamond cutting wheels are of
the correct size for the device.
•
Diamond cutting wheels must be handled
and stored with care in accordance with the
manufacturer's instructions.
•
Examine the diamond cutting wheels each
time before using them. Never use products
which have parts broken off or are cracked or
in any other way damaged.
•
Check that the diamond cutting wheels
have been fitted in accordance with the
manufacturer's instructions.
•
Ensure that the diamond cutting wheels are
correctly fitted and fastened before you start
to use the device. Allow the tool to run without
load and in a safe position for 30 seconds;
stop the device immediately if it vibrates hea-
vily or if any other faults become apparent. If
this should be the case, examine the machine
to find the cause.
•
Never use separate reducer sleeves or ad-
apters to make diamond cutting wheels with
larger holes fit onto the device.
•
Before using the device, take precautions to
ensure that flying sparks do not cause any
danger (e.g. hit anyone or cause inflammable
substances to ignite).
•
If dust is generated during working, ensure
that the air vents are kept clear. If you should
have to remove dust, disconnect the electric
tool from the mains power supply first (use
non-metallic objects only) and take care not
to damage any parts inside the tool.
•
The wheels will continue to turn for a while
after the tool has been switched off.
•
Never subject the diamond cutting wheels to
any pressure from the side. Always switch off
- 17 -
14.02.2018 08:58:49 14.02.2018 08:58:49