Important - EINHELL TC-TS 315 U Manual De Instrucciones Original

speed of rotation before commencing with
the cut.
•
To turn the equipment off again, press the red
button „0".
Overload cut-out (Fig. 23)
The motor of this equipment is protected against
overload by an overload switch (52). If the rated
current is exceeded, the overload switch (52) will
shut down the equipment.
•
Let the equipment cool down for several mi-
nutes.
•
Press the overload switch (52).
•
Press the green button „I" to switch on the
equipment.
7.2 Cutting depth (Fig. 1)
Turn the hand crank (8) to set the blade (4) to the
required cutting depth.
Turn anti-clockwise:
larger cutting depth
Turn clockwise:
smaller cutting depth
7.3. Parallel stop
7.3.1 Stop height (Fig. 12-14, 2b)
•
Use the holder (24) together with the parallel
stop rail (23) as a parallel stop.
•
The parallel stop supplied with the bench-ty-
pe circular saw has two different guide faces.
•
For thick material you must use the stop rail
(23) as shown in Fig. 12, for thin material you
must use the stop rail as shown in Fig.13.
•
To change over the stop rail (23) to the lo-
wer guide face you have to slacken the two
knurled screws (26) in order to disconnect the
stop rail (23) from the holder (24).
•
Remove the two knurled screws (26) through
the one slot (25) in the stop rail (23) and in-
sert in the other slot (27).
•
Remount the stop rail (23) on the holder (24).
•
The procedure for changing over to the high
guide face is similar.
7.3.2 Cutting width (Fig. 12/13)
•
The parallel stop (7) has to be used when
making longitudinal cuts in wooden workpi-
eces.
•
The parallel stop (7) can be mounted on the
right-hand side of the saw table (1).
•
The parallel stop (7) has to be mounted in the
guide rail (28) of the saw table (1).
Anl_TC_TS_315_U_SPK9.indb 34 Anl_TC_TS_315_U_SPK9.indb 34
GB
•
The parallel stop (7) can be set to the requi-
red dimension with the help of the scale (22)
on the table.
•
Use the locking grip (12) to secure the paral-
lel stop (7) in the guide rail (28) and hence the
desired cutting width.
7.3.3 Setting the stop length (Fig. 14)
•
The stop rail (23) can be moved in longitudi-
nal direction in order to prevent the workpiece
from becoming jammed.
•
Rule of thumb: The rear end of the stop co-
mes up against an imaginary line that begins
roughly at the center of the blade and runs at
an angle of 45° to the rear.
•
Set the required cutting width
- Slacken the knurled screws (26) and push
the stop rail (23) forward until it touches the
imaginary 45° line.
- Retighten the knurled screws (26).
Warning! The gap between the saw table (1) and
the underside of the stop rail (23) must not be too
large in order to prevent the material getting jam-
med. To adjust the distance, the parallel stop (7)
must be fastened fi rst using the locking grip (12).
Then slacken the knurled screws (26), lower the
stop rail (23) down to the saw table (1) and secu-
re the knurled screws (26) again afterwards.
7.4 Cross stop (Fig. 15)
•
Use the holder (24) together with the cross
stop rail (23) as a cross stop.
•
Slide the cross stop into the guide rail (41) on
the left-hand side on the saw table.
•
Undo the locking grip (20).
•
Turn the stop rail (23) until the arrow points to
the angle required.
•
Re-tighten the locking grip (20).

Important!

•
Do not push the stop rail (23) too far toward
the blade.
•
The distance between the stop rail (23) and
the blade (4) should be approx. 2 cm.
7.5 Setting the angle (Fig. 16)
•
Slacken the locking grip (9) at the front and
rear of the housing (44).
•
Move the housing (44) until the pointer (46)
points to the desired angular setting on the
scale (45).
•
Lock this setting with the locking grip (9) at
the front and rear of the housing (44).
•
If needed, the end stop for adjusting the angle
- 34 -
23.03.2020 09:09:29 23.03.2020 09:09:29