Vertical Steam; Multiple Descaling System; Anti-Drip System - Siemens sensorSteam TS12 Serie Instrucciones De Uso

8

Vertical steam

This can be used to remove creases from
hanging clothes, curtains etc.
Warning.
Do not iron clothing while it is being worn!
Never spray or aim the steam at persons or
animals!
1. Set the temperature control (15) to the "•••"
or "max" position.
2. Models with steam activation button (2*).
• Grip the handle (1) and set the steam setting
to the "max" position.
• Or set the steam setting to the
and press the steam activation button (2*).
Models without steam activation button (2*):
• Grip the handle (1) and set the steam control
to the "max" position.
3. H old the iron in an upright position about 15 cm
away from the garment being steamed.
The shot of steam button (6) on the handle may
be additionally pressed at intervals of 5 seconds.
However, after 4 shots of steam, wait for 10
seconds to allow for continued steam production.
Multiple descaling
9
system
Depending on the model, this range of irons is
equipped with the following de-scaling features
"AntiCalc".
1. self-clean
The self-clean ilter between the water tank and
the pump prevents scale impairing the steam
generation system and ensures the optimum
production of steam.
2. anti-calc
The "anti-calc" cartridge has been designed to
reduce the build-up of scale produced during
steam ironing, helping to extend the useful life of
your iron. Nevertheless the "anti-calc" cartridge
cannot prevent all of the scale that is produced
naturally over time.
3. calc'n clean
The "calc'n clean" function helps to remove
scale particles out of the steam chamber. Use
this function approximately every 2 weeks, if the
water in your area is very hard.
Follow the procedure described below:
a) Remove the plug from the socket, ensure that
the iron has cooled down and that the water
tank (11) is empty.
b) Set the temperature control (15) to the "calc'n
clean" setting.
18
S I EMENS
c) Fill the water tank (11) to the maximum level
with clean tap water.
d) Plug in the iron and select the maximum steam
setting "max" by pressing the steam selection
button (4).
e) Hold the iron over a sink or a container to
collect the water.
f) Grip the handle (1) until the water tank (11) is
empty. This could take several minutes.
g) Repeat the procedure until particles no longer
come out of the soleplate (13) of the iron.
h) Turn the temperature control (15) to the
maximum setting. The iron will begin to emit
steam. Wait until the water inside the iron has
evaporated.
i) Clean the soleplate (13) of the iron.
position
4. calc'n clean with descaling luid
(model dependent)
For deep descaling, use the descaling luid (17*)
supplied.
This should be carried out every 3 months.
The descaling luid (17*) can be obtained from
our After-sales service or from our website.
Accessory code
(After-sales)
311144
Follow the procedure described below:
a) Remove the plug from the socket, ensure that
the iron has cooled down and that the water
tank (11) is empty.
b) Set the temperature control (15) to the "calc'n
clean" setting.
c) Fill the water tank (11) with tap water mixed with
a measure (25 ml) of the descaling luid (17*).
d) Plug in the iron and select the maximum steam
setting "max" by pressing the steam selection
button (4).
e) Hold the iron over a sink or a container to
collect the water.
f) Grip the handle (1) until the water tank (11) is
empty.This could take several minutes.
g) Then follow the procedure described above in
section "3. calc'n clean" until particles no longer
come out of the soleplate (13) of the iron.

Anti-drip system

If the temperature control (15) is set too low
(below "••"), the steam is automatically switched
off to prevent water from dripping out of the
soleplate (13).
The "activeControl Advanced" indicator lamp (3)
on the handle lashes and the pump will not work.
Name of accessory
(Online shop)
TZ11001