HQ-Power VDLP36CW Manual Del Usuario página 3

• Do no ot switch the dev
devic e against damag
• This d device is designe
indoo or with an altern
• Lighti ing effects are no
• Use t he original packa
• Keep this manual for
• There e may be some s
and a any smoke or sm
• Repla ace the shields, le
to suc ch an extent that
4. Ins stallation
a) Co olour wheel
1) 1 Carefully rem
2 2) Unscrew the
3 3) Place the colo
b) La amps
• Only fit or re
• Let a lamp co
operation.
• Do not install
• Replace any d
• Install 1 x wh
(green), LAM
P Procedure
1) Turn the
2) Remove
3) Fasten th
clockwise
Remark: Do not R
c) Ov verhead mount
Risk of in
determinin
regularly.
installation
• Have the dev
norms.
• The construct
the device fo
• The installatio
• Never stand d
qualified tech
• Install the de
• For truss-mo
the (folded) b
• Adjust the de
16.03.201 1
vice on immediate ely after it has be
ge by leaving it sw witched off until
ed for professiona al use on stage, i
ating current of 230 VAC~50 Hz.
ot designed for p permanent operat
aging if the devic ce is to be transp
future reference. .
moke or a partic cular smell when
ell will gradually disappear.
enses or UV scre ens if they have
t their effectiven ess is impaired.
move the protecti ve film from the
screw of the axle e
our wheel in fron nt of the axle and
place a lamp whe en the device is u
ool down before r replacing it as th
l lamps with a hig gher wattage tha
deformed or dam maged lamp with
hite lamp (LAMP P36 (30W/6.4V))
MP36R (red), LA AMP36Y (yellow)
fixation ring ant ticlockwise and re
the lamp and loo osen the wires.
he wires to the n ew lamp. Put the
e to fix it.
t operate the de evice if the lam
ing
jury. Overhead mounting require
ng the installation n material to be u
Do not attempt t to install the dev
n may result in in njuries.
vice installed by a a qualified person
tion to which the e device is attach
r one hour witho ut deformation.
on must always b be secured with a
directly below th e device when it
hnician check the e device once a y
evice in a location n with few passer
unting, use an ap ppropriate clamp
bracket.
esired inclination angle via the mo
VDLP36 6CW
een exposed to c
it has reached ro
n discos, theatre
tion: regular ope
ported.
the device is act
become visibly d
colour wheel
d fasten it with th
unplugged from t
e temperature of
an that for which
a lamp of the sa
or 1 coloured la
).
emove it.
e lamp in the hou
p is not secure
es extensive expe
used... Have the
ice yourself if yo
n, respecting EN
ed should be abl
a secondary atta
is being mounte
ear and once bef
rs-by and inacces
p (not incl.) and f
ounting bracket a
3
changes in tempe erature. Protect t
oom temperature e.
es, etc. The VDLP P36CW can be u
eration breaks wil ll prolong their liv
ivated for the firs st time. This is n
damaged (e.g. cr racks, deep scratc
he screw.
the mains.
f a lamp can reac ch 130°C during
the device was d designed.
ame type.
mp (LAMP36B ( (blue), LAMP36G
using and turn th e fixation ring
ly fastened.
erience: calculat ing workload lim
material and the e device itself che
u lack these qua lifications as imp
60598-2-17 and d all other applica
e to support 10 t times the weight
chment e.g. a sa afety cable.
ed, removed or se erviced. Have a
fore you bring it into service.
ssible to unautho orised persons.
fit an M10 bolt th hrough the centre
and tighten the b bracket screws.
Re v. 03
the
used
ves.
ormal
ches)
G
its,
ecked
proper
able
t of
e of
©Vellema an nv