Switching On/Off - Festool DSC-AG 125 Manual De Instrucciones

Ocultar thumbs Ver también para DSC-AG 125:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 33
cutting performance of the machine (periph-
eral speed of the grinding and cutting wheels).
 Set the sliding stop for cut depth [2-5] on scale
[2-4] to a depth value of 10 mm.
 Push the arresting button [1-1] and push the
cover in.
 Release the arresting button [1-1] and let the
cover be arrested when it gets to the set depth.
 Unlock with button [2-1] and fully open the disc
cover.
 Clean the fl ange [6-4] and clamping nut [6-2],
as well as the clamping faces of the cutting
disc [6-3].
 Put the fl ange [6-4] on the grinder's spindle
with the shoulder facing outward.
 Put on the disc [6-3]; take care to comply with
the prescribed direction of rotation (arrow on
the disc vs. arrow on the machine). The fl ange
shoulder must exactly fi t in the disc's opening.
 Screw on the clamping nut [6-2] with the shoul-
der facing outward (from the disc), press on the
spindle arrest and tighten with wrench [6-1].
 Close the disc cover.
 Before switching on, check free rotational
movement of the disc.
8.2
Guide system [fi gure 7]
WARNING
Only use discs of thickness up to 3 mm!
Use the guide bar [7-1] for accurate cuts.
The side clearance of the disc guiding can be set
with the aid of the adjusting screws [1-9].
Guide bars
On the bottom face of the guide bar there are anti-
skid strips, which ensure safe contact and prevent
the workpiece from scratching.
The bar can also be secured with the aid of special
clamps FSZ 300 [7-2], pushed into the special
guide grooves. Safe guiding on uneven surfaces
is thus enabled.
WARNING
The guide bars are equipped with burr protec-
tor, which must be cut off before the fi rst use.
Connector
Depending on the particular application and the
workpiece size, several guide bars can be con-
nected with the aid of a connector spring [7-3].
Fast connection of guide bars can be secured by
screws in the threaded openings.
9
Activation
WARNING
Risk of accident if the machine is operated us-
ing unauthorised voltages or frequencies.
 The mains voltage and the frequency of the
power source must correspond with the spec-
ifi cations on the machine's name plate.
 In North America, only Festool machines with
the voltage specifi cations 120 V/60 Hz may
be used.
Set the sliding stop for cut depth [2-5] on scale
[2-4] (top edge of the stop) to the requested depth
of the cut – loosen and tighten the stop screw [2-
6] as necessary.
The cut depth scale is valid for cutting without a
bar.
The scale is for orientation only. The actual depth
of the cut may be affected by, for example, manu-
facturing tolerances or the wear of the diamond
disc's segment. If en exact depth is required, it
is necessary to measure the actual depth on a
test cut.
9.1
Switching on – off
Switching on
 Slide the on/off switch [1-5] forwards.
 Continuous operation: pressing the front part
of the switch at the same time locks the on/
off switch.
The electric power tool starts.
Only make contact with the material once the
machine has reached operating speed.
Switching off
 Lift the electric power tool from the processed
material.
 Release the on/off switch [1-5].
 During continuous operation: press on the
rear part of the on/off switch [1-5].
WARNING
Risk of injury
Rebound, ejected parts
 Before setting down the machine, wait until
the rotating tool has come to a complete stop.
21

Publicidad

Tabla de contenido
loading

Tabla de contenido