Magnat MAGNASPHERE 55 Manual De Instrucciones página 13

CONTROLS FOR ACTIVE SPEAKER (BACK SIDE) (FIG. 2)
(4) Mains connection
(5) Power switch
(6) SPEAKER CONFIG: Loudspeaker configuration
•
LEFT: Stereo operation, left speaker
• MONO: Mono operation, the two stereo channels are added together
•
RIGHT: Stereo operation, right speaker channel
(7) BASS: Bass reproduction adjustment -2dB, 0dB, +2dB
(8) TREBLE: Treble reproduction adjustment -2dB, 0dB, +2dB
(9) ZONE SELECT: Assignment of the speaker to a listening zone A, B or C
TRANSMITTER CONTROLS (FRONT, RIGHT SIDE) (FIG. 3)
(10) LED status display:
Red: Standby mode
Red, flashing: Operating mode, connected to the transmitter
Green: Operating mode, connection to speaker established
Blue, flashing: Bluetooth® pairing mode
Red/blue flashing: Establishing connection to loudspeaker
(11) BT-PAIR: Activates the Bluetooth® pairing mode
TRANSMITTER CONTROLS, CONNECTIONS (REAR) (FIG. 4)
(12) ANALOGUE INPUT, LINE IN 1 and LINE IN 2: Analogue inputs with RCA connector (LINE IN 1) or 3.5mm jack connector (LINE IN 2).
(13) DIGITAL INPUT, OPTICAL 1 and OPTICAL 2: Digital inputs with TOSLINK® connector.
(14) DIGITAL INPUT, USB: USB audio input with USB type B connector .
(15) Transmitter ID: Selects the transmission frequency
F-1: 5.2GHz (default setting)
F-2: 5.8GHz
F-3: 2.4GHz – Please note that, with this setting, the Buetooth input is not available for system-related reasons!
(16) Voltage supply connection (E).
OPERATION WITH THE SYSTEM REMOTE CONTROL (FIG. 5)
(17) POWER: Switches on all speakers in a zone if these are in standby mode. Conversely, all the speakers in a zone can be switched
from operating mode to standby mode.
(18) LINE 1/2: Switches the device over to the analogue inputs LINE 1 (press once) or LINE 2 (press twice). Ln1 or Ln2 is shown in the
display.
(19) OPT 1: Switches the device over to optical digital input 1 OP 1 is shown in the display.
(20) OPT 2: Switches the device over to optical digital input 2 OP 2 is shown in the display.
(21) USB: Switches the device to the USb input. UB is shown on the display.
(22) BT: Switches the device to the Bluetooth® input. The blue LED status indicator (Fig. 1, (1)) flashes or illuminates (see section
System installation - Connecting to a Bluetooth® audio source). bt is shown on the display.
(23) TRANSMITTER: Selects the transmitter ID (F1, F2, F3). The speakers connect to the transmitter, which is set to the corresponding
transmitter ID (see transmitter controls, item 15). F-1, F-2 or F-3 is shown in the display.
(24) VOLUME: Increases (+) or decreases (-) the volume.
(25) MUTE: Switches the sound on and off.
LOUDSPEAKER SET INSTALLATION
Positioning the loudspeakers:
The Magnat Magnasphere speakers should, where possible, be set up without any obstructions and slightly inclined towards the
listening position.
In addition, the Magnasphere 33 shelf-top speakers should be positioned more or less at ear level (shelf, sideboard or the like).
In the ideal configuration the speakers and the listening position should form an equilateral triangle. When the left and right speakers
are the same distance from the listening position their sound arrives at the same time, resulting in a harmonious, natural music
reproduction.
There should be a clear line of sight between the loudspeakers and the listening position. Any sound-absorbing or reflecting obstacles
in the path will distort the sound.
Now configure the two loudspeakers using the switch at the rear (item 6) and select the same zone A, B or C for both speakers (rotary
switch item 9).
13