Magnat MAGNASPHERE 55 Manual De Instrucciones página 14

Please note: All loudspeakers configured to the same zone are controlled synchronously (power, volume, input, transmitter selection).
This means as soon as the settings of a loudspeaker are changed using the remote control, these changes also take effect for all
speakers in the same zone.
Positioning the transmitter:
The transmitter should logically be positioned close to the audio sources being connected to the system (stereo system, TV, set top
box, etc.).
CONNECTING AUDIO SOURCES TO THE TRANSMITTER
1. Connecting to an analogue audio output with cinch output terminals (CD player, tuner, audio amplifier, AV receiver, etc.)
Connect the audio source to the LINE IN 1 input (item 12) using the cable supplied (F)
2. Connecting to a headphone output or preamplifier output with a 3.5 mm jack socket (e.g. smartphone)
Connect the audio source to the LINE IN 1 input (item 12) using the cable supplied (G)
3. Connecting to a computer with a USB port
Connect the transmitter's USB audio input port (item 14) to a computer USB output using the type A to type B cable supplied (l). A
driver is not required. If you are prompted to make a selection, please select the SPDIF interface „Magnat Magnasphere".
4. Connecting to digital audio sources
Connect one of the transmitter's digital audio inputs (item 13) to the digital output on your CD player/computer/games console/
network player, etc. using an optical digital audio cable. The digital inputs can be selected separately, therefore it is possible to
connect two digital sources simultaneously.
Please note: The digital inputs are suitable for stereo signals up to 24 bit/96kHz.
5. Connection to a Bluetooth® device
Select the Bluetooth® input (remote control, item 22). If you have previously connected a Bluetooth® device, the loudspeaker will
automatically attempt to re-establish a connection with this device. If this is the case, you may be required to manually reconfirm the
connection on the source device.
If a connection has not already been made or the connection cannot be re-established, activate the „pairing mode". To switch the
loudspeaker to pairing mode, briefly press the BT PAIR button (Fig. 11, (8)) on the right of the transmitter. The LED on the front of the
transmitter (item 10) will flash blue rapidly as long as the pairing mode is active.
Now activate the Bluetooth® mode on your source device. The speaker will appear in the list of Bluetooth® devices as „Magnat
Magnasphere". If it is not displayed in the list, set your source device to search for Bluetooth® devices manually and make sure that
the speaker has been switched to the pairing mode.
Depending on the source device, you may be asked whether the password is to be accepted during the pairing procedure. You can
confirm this by simply pressing „Accept". If you are still asked for a password, use the default passwords „0000" or „1234". If you
are asked if you want to establish a connection after pairing, please select „Yes". When the device has been paired and connected
successfully the Bluetooth® LED status indicator will illuminate continuously and the STBY-Pair LED goes out.
The loudspeaker supports the Qualcomm® aptX™ high quality audio transmission standard. If your source device also supports this
standard, "Qualcomm® aptX™" will be selected automatically as the transfer mode when establishing a Bluetooth® connection.
Please note: Please check whether the output of the audio source
a) has a fixed volume level or
b) the level can be adjusted with the volume controller of the audio source.
In case a) you can adjust the volume using the remote control of the MAGNASPHERE; in case b) the level of the audio source should be
set to a maximum level where no distortions can be heard at the highest volume setting of the MAGNASPHERE. The volume of the audio
source should also be taken into account. No distortions should be evident here either.
CONNECTING THE POWER SUPPLY OF THE TRANSMITTER AND THE ACTIVE SPEAKERS
Two power cables are supplied for the two floor-standing speakers. The mains cable used in your country, however, may be different. If
the mains cable is not compatible with your power sockets or if you are in any doubt, please contact your MAGNAT dealer.
1. Connect the power cables to the sockets (Fig. 4 (12)) and (Fig. 5 (24)) on the amplifier of the right and left speakers.
2.
Plug the power cable into the power socket. Make sure that you are using the mains plug that is compatible with the socket (refer to
the information above).
CONNECTING THE TRANSMITTER'S POWER SUPPLY
The power for the Magnasphere TX11 transmitter is supplied via a plug-in power supply.
The power supply is provided with 3 mains adapters:
1. Euro plug (type C, CEE 7/16)
2. Commonwealth plug (type G, BS 1363)
3. NEMA-1 plug (type A)
Please choose the mains adapter that fits your power sockets at home.
The adapter is inserted in the recess with the nose facing outwards and is pressed down until it clicks into place.
Then connect the cable with the plug to the socket (16) at the rear of the transmitter and plug the power supply into a socket.
14