Multi-Zone Operation - Magnat MAGNASPHERE 55 Manual De Instrucciones

INSERT THE BATTERIES IN THE REMOTE CONTROL
The battery compartment in the remote control is located on the lower narrow side and is secured with a Philips screw. Loosen the screw
using the screwdriver provided and insert the batteries (2 x type AA) as illustrated on the back of the remote control.
Close the battery compartment and tighten the screw.
OPERATION OF THE MAGNASPHERE LOUDSPEAKER SET (SINGLE ZONE, STEREO OPERATION)
1. Checking the zone: Makes sure the same zone is set for both speakers (rear of loudspeaker, item 9)
2. Set the loudspeaker configuration: Set the switch (6) on the left speaker seen from the listening position to LEFT, and that on the
right speaker to RIGHT.
3. Select the transmission frequency (transmitter ID): The transmission frequency can be set via the transmitter ID switch on the
transmitter (item 15):
•
F1 (5.2GHz, default setting): Provides for very low interference at medium range (within a room or over 2-3 rooms)
•
F2 (5.8GHz): Provides for very low interference at short to medium range (within a room or between 2 neighbouring rooms)
• F3 (2.4GHz): This setting enables greater ranges (also on neighbouring floors). As this frequency band is used by a very large
number of devices (WLAN, Bluetooth®, etc.), disruptions in operation can occur in unfavourable conditions. Please note that, with
this setting, the Bluetooth® input is not available for system-related reasons.
4. Make sure the two speakers are connected using the power cables supplied and that the transmitter is connected to a mains socket
via the power supply.
5. Now switch on the two speakers via the power switch (item 5) at the rear. The speakers are now in standby mode, the LED in the
speaker display (1) lights up red (dimmed).
6. Switch on the speakers via the button (17) on the remote control. Select the transmitter ID selected under point 3 via the buttons 23.
Once the speaker is paired with the transmitter, the LED (1) lights up red. The LED on the transmitter (10) lights up green.
7. Select the desired input source via the buttons 18-22.
8. Adjust the volume via button 25.
Please note:
• The Magnasphere speakers store the volume set when the system is switched off. This volume is reset automatically when the
system is switched on again. However, if the volume is greater than 20, the volume is always set at 20 when the system is switched
on again.
•
If no signal is reproduced by the loudspeaker over a period of 12 minutes (display (2) flashes), the speaker switches to standby mode
automatically.
• If a loudspeaker is not connected to a transmitter (no power to transmitter or different transmitter ID's set), the LED in the speaker
display (1) and the LED on the transmitter (10) flash red, and the speaker switches to standby mode automatically after around 3
minutes.

MULTI-ZONE OPERATION

The Magnasphere system can be expanded to up to 3 zones. The zones are named A, B and C.
The zone is configured using the ZONE SELECT switch (9) on the back of the loudspeaker.
All speakers assigned to the same zone (e.g. zone A) are controlled synchronously (power, volume, input). It does not matter which
loudspeaker receives the remote control signal.
If a speaker is assigned to another zone (e.g. zone B), control is independent of the first zone (A). This means that volume and input can
be set independently for each zone.
Please note:
• The USB input and the Bluetooth® input use the same transmission channel,
• i.e. if Bluetooth® is selected as the input in one zone, the USB input cannot be selected at the same time by another zone and vice
versa. The following then appears in the display ---
• The LINE 1 input and the LINE 2 input use the same transmission channel, i.e. if LINE 1 is selected as the input in one zone, the LINE
2 input cannot be selected at the same time by another zone and vice versa. The following then appears in the display ---. The LINE
input can be changed by prolonged pressing of the LINE 1/2 button. However, this change then takes effect in all zones.
CAUTION
Interfering with the speaker or accessories shall result in the expiration of the operating licence. The supplied accessories are to be used
for operation. Additional accessories must be intended for the purpose at hand and in perfect working order.
15