Battery; Battery Charger; Battery Charger Configuration; Accessories - Comet Spa CRS 66 BT Manual Del Usuario

1 Squeegee bumper wheels
2 Squeegee blades replacement knobs
3 Squeegee fast fixing knob
4 Squeegee inclination adjusting knob
5 Suction hose
6 Squeegee pressure fixing knobs
7 Squeegee wheels
Photo F
1 Solution water filter
Photo G
1 Battery compartment with 6V batteries
2 On- board battery charger
3 Battery charger plug
4 Battery connection diagram
Photo H
1 Detergent solution ouflow adjusting lever
2 Battery security connector
2 Brush plate lifting/lowering lever
Photo I
1 Battery charger cover
2 Red LED - Battery discharged
3 Green LED - Full charged battery
4 Dip-Switches
5 Plastic cap to access the Dip-Switches
6 Dip-Switches for PB-Acid/GEL battery
setting
7 Table with Dip-Switch settings for
PB-Acid/GEL charging curve
Photo L
1 Unblocking lever of the electromechani-
cal brake in working position
(brake applied)
2 Unlocked position of the
electromechanical brake
Photo M
1 Steering wheel
2 Control panel with display
3 General ON/OFF key switch
4 Detergent tank
Photo N
1 Brush motor operating push button
2 Suction motor operating push button
3 Detergent outflow adjusting push button
4 Forward/reverse traction push button
selector
5 Traction speed increase push button
6 Traction speed reduce push button
7 Operating informations display
Photo O
Percentage of dilution of the detergent
1 Dilution with half outflow of clean water
2 Dilution with complete outflow of clean
water
5.2.2

BATTERY

If supplied, the Pb-Acid (if not dry charged) or gel batter-
ies are ready to be installed:
Positive pole - red
Negative pole - black.
5.2.3

BATTERY CHARGER

If supplied, refer to the corresponding booklet.
5.3

BATTERY CHARGER CONFIGURATION

• We recommend to call the assistance centre or a tech-
nician if you have problems with the setting given.
The machine is equipped with a battery charger configu-
rated for PB-Acid batteries
If the operator whish to use GEL / AFGM batteries, it is
necessary change the battery charger settings as follows:
• DISPLAY OF THE BATTERY CHARGER SETTINGS
The battery charger settings are shown by the blinking
of the LED indicator when the battery charger is switch-
ing on:
- the RED LED indicator ( Photo I - 2 ) flashes 2 times =
the battery charger is set for PB-Acid batteries
- the GREEN LED indicator ( Photo I - 3 ) flashes 2 times
= the battery charger is set for GEL batteries
The battery charger settings will be displayed even if bat-
teries are not connected.
• DIP-SWITCH CONFIGURATION FOR BATTERY CHARGER
CBHD2 24V 20A
To set the charging curve type for Pb-Acid or GEL/AGM
batteries it is necessary to operate on the dip-switches
placed inside the battery charger ( Photo I -4 ).
The dip-switches for the setting of the charging curve are
on the control card ( Photo I - 4 ) that is placed behind
the lower panel of the battery charger ( Photo I - 1 ). It is
also possible to reach the dip-switches by removing the
plastic cap ( Photo I - 5 ). For the setting of the charging
curve it is necessary to operate on the dip-switches of the
group indicated as SW1 ( Photo I - 6 ), placing them as
shown in the table ( Photo I - 6) at page 7.
NOTE: The dip-switches of the group indicated as SW2
must always be set in the OFF position.
5.4

ACCESSORIES

Your machine supplier can provide a complete and up-
dated list of all available accessories, such as brushes, pad
drivers, disks, etc.

6. INSTALLATION INFORMATION

6.1

BATTERY PREPARATION

• The technical features of the batteries used must
match those indicated in the technical features section.
Using different batteries may cause serious damage to
the machine or may require them to be charged more
frequently.
• During installation or when performing any type of
battery maintenance, the operator must be equipped
31