Publicidad
Idiomas disponibles
Idiomas disponibles
ENG
Instruction Manual for recessed floor light N-TIC
1.
Use as directed:
This product serves exclusively lighting purposes and may:
only be operated using a suitable transformer, output: 12V.
not be exposed to strong mechanical loads or to strong contamination.
only be installed and operated after a condition inspection if the product
is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2.
Technical Data:
Operating voltage:
12V
Safety class:
III
Safety type:
IP 67
Bulb:
QR51, G5,3, max. 35W
Recess dimensions(Ø/D):
10,5/11cm
Swivel range:
20°
Weight:
0,6 kg
Importeur:
SLV Elektronik GmbH
IP 67: Protection against dust(dust-tight) - Protection against the
penetration of water when temporarily submerged.
3.
Installation
The complete installation must be done by an electrical expert,
who is familiar with the valid directives.
Attention: Switch off power of the mains supply or respectively of the
connection lead before doing any works.
Use only parts, which are supplied with the product or are described as
accessories! Otherwise the product or the installation might not be
sufficiently safe!
Indication for the installer: In case you do not install a completely
supplied system (with transformer), you are considered a "manufacturer" by
the low-voltage directive. In this case you are required to ensure the
conformity of the whole system and declare it by attaching the CE-sign.
Installation place:
The product is suited for recessed floor installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background. The light exit should be placed at least so far from the
illuminated surface, as indicated as minimum distance on the type plate of
the luminaire:
0,5 m
. Pay special caution to easily inflammable objects
(e.g. foliage).
Preparing the low-voltage(12 V) power supply
The transformer should be used up to 80 % of its capacity. The total watt
power of the connected light fittings must not exceed the power output of
the transformer. The distance between spot and transformer should be at
least 20 cm. The conductor length between a electronical transformer and a
lamp may not be longer than 2 metres (Electromagnetic Emission). Note
the manufacturers information for the transformer.
Separate Installation Steps
Prepare the power supply.
Prepare the recess and a blank tube(A), that leads to the powers supply.
Fix the plastic casing firmly into the earth.
Loosen the screws on the shield - take off the shield and the protection
glass with the gasket.
Direct the connection lead through the blank tube and connect it to the
power supply.
Inserting the bulb: Stick the bulb into the socket. Adjust the swivel
range by turning the two screws on the socket.
Insert the fixture into the plastic casing.
Put the protection glass with gasket on the fixture. The part of the gasket
that is jutted out must point downwards. Fasten the stainless steel shield
back on the fitting. Fasten the screws crosswise. Exchange two of the
shorter screws with the supplied longer screws to fix the fixture to the
plastic casing.
The product is now ready for operation.
4.
Operation
:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
10,5cm
How to avoid failure and fire risk:
Do not cover the product (Remove leaves and dirt once in a while).
Do not fasten anything on the product.
Replace damaged protection glasses immediately!
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
What is to do if a bulb is defect or does not work?
Disconnect the product from power, before you exchange the bulbs.
Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb: see Installation.
5.
What else has to be considered?
Disconnect the product from power, before you...
clean or maintain the product.
do any works on the product or its components (electric expert).
F
Mode d'emploi pour encastré N-TIC
1.
A utiliser comme indiqué :
Ce produit ne sert qu'à éclairer:
être exploités seulement avec un transformateur adéquat, avec une
tension de sortie: 12V.
il ne doit être soumis ni aux efforts mécaniques importants ni à un
encrassement important.
il ne doit être utilisé qu'après examen si le produit a été stocké dans un
entrepôt humide ou sale.
il ne doit pas être modifié.
Un non-respect de ces points peut causer un court-circuit ou une
décharge électrique!
2.
Informations techniques:
Tension d'alimentation:
12V
Classe de protection:
III
Degré de protection:
IP 67
Ampoule:
QR51, G5,3, max. 35W
Mesures d'installation(Ø/P):
10,5/11cm
Portée d'inclinaison:
20°
Poids:
0,6 kg
Importateur:
SLV Elektronik GmbH
IP 67: Protection contre la pénétration de poussière - Protection
contre la pénétration de l'eau en cas d´immersion temporaire.
3.
Assemblage
L'installation complète ne doit être faite que par du personnel
qualifié en électrotechnique qui connaît les directives.
Attention: Mettez l'alimentation électrique ou le raccordement au
secteur hors tension avant de travailler! Utilisez seulement des pièces qui
ont été livrées avec le produit ou qui sont uniquement décrites comme
accessoires ! Sinon, l'installation ainsi que le produit ne peuvent pas être
garantis.
Indication pour l'installateur: même si vous n'installez pas
l'installation complète du système (avec transformateur), vous êtes
considéré comme fabricant en fonction de la directive basse tension. Dans
ce cas, vous aurez à produire la preuve de conformit.
Lieu d'installation
Ce produit est fait pour une installation au sol.
Fixez le luminaire sur une surface stable pour éviter des accidents. La
distance entre la sortie de lumière et la face illuminée devrait au moins
Publicidad
