Footswitch - Fender Hot Rod DeVille ML Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 11
VOLUME 1
VOLUME 2
6 7
INPUTS
5
8
5
1
2
4
9
4
3
10
3
2
11
2
1
12
1
NORMAL
BOOST
BRIGHT
A. INPUT 1 — A normal sensitivity input, ideal for use with
most guitars.
Either input jack can be used with any type of guitar
depending on the tone character you prefer. Experiment
and use the input that sounds the best to you.
B. INPUT 2 — A lower sensitivity input (–6dB) that provides
cleaner response with high-output and pre-amplified guitars.
You can use Input 1 and Input 2 simultaneously with two
guitars or a guitar and a microphone, for example. Input
sensitivities become equal when used simultaneously.
C. NORMAL / BRIGHT — Press IN to boost the high-
frequency tones.
Normal
D. VOLUME 1 — Adjusts the loudness of the amplifier when
Volume 1 is selected.
E. BOOST — Press IN to boost the gain and distortion when
Volume 2 is selected (Note: The BRIGHT switch is disabled
when BOOST is selected).
Normal
F.
VOLUME 2 — Adjusts the loudness of the amplifier
when Volume 2 is selected.
G. CHANNEL INDICATOR —
Off  Volume 1
Yellow  Volume 2
Red  Volume 2 with Boost selected
H. TREBLE — Adjusts high-frequency tone.
I.
BASS — Adjusts low-frequency tone.
J.
MIDDLE — Adjusts mid-frequency tone.
K. VOLUME SELECT — Press to switch between active
volume controls.
Volume 1
L. REVERB — Adjusts the level of the Reverb effect.
M. PRESENCE — Adjusts tone at a point in the signal path
after the distortion circuitry to provide unique ultra high-
frequency tone shaping.
TREBLE
BASS
MIDDLE
6 7
6 7
6 7
8
5
8
5
8
5
9
4
9
4
9
4
10
3
10
3
10
3
11
2
11
2
11
2
12
1
12
1
12
Bright
Boost
Volume 2
REVERB
PRESENCE
6 7
6 7
8
5
8
9
4
9
4
10
3
10
3
11
2
11
2
1
12
1
12
VOLUME
SELECT
N. PREAMP OUT / POWER AMP IN — Multi-functional
input/output jacks that can be used in a variety of
configurations:
(1) Effects Loop—Connect PREAMP OUT to the input of
your effects device and connect the effects output
to the POWER AMP IN jack.
(2) Multiple Hot Rod Amps—Connect PREAMP OUT on
the primary unit to POWER AMP IN on the auxiliary
unit. The primary unit is used to control the auxiliary
unit, except for REVERB and PRESENCE which remain
active on the auxiliary unit.
(3) Recording or Sound Reinforcement—Connect
PREAMP OUT to the input jack of sound equipment.
Use instrument (shielded) cables with TS (Tip-Sleeve)
plugs
POWER AMP IN jacks are located before Reverb and
Presence in the signal path.
O. FOOTSWITCH — Connect
included footswitch here to enable
remote selection of the Volume 1
/ Volume 2 / Volume 2 with Boost
channels. The VOLUME SELECT {K} button on the control
panel is disabled when the footswitch is connected.
Speaker cable (unshielded) is superior to instrument
cable (shielded) for connecting the footswitch.
P. POWER INDICATOR — Illuminates when the unit is ON.
Unscrew the red jewel to access the bulb (type T47) for
replacement.
Q. STANDBY — Use Standby instead of switching the
power off during short breaks to avoid having to wait
for the tubes to warm up when you want to start playing
again. Also, keep the amplifier on Standby for the first 30
seconds when you first switch the power on to give the
tubes a gentle warm up cycle.
Using Standby will extend the life span of your
amplifier's vacuum tubes by reducing the shock of the
heat-up / cool-down cycle on the tube filaments.
R. POWER SWITCH — Switches the unit ON/OFF.
6 7
PREAMP
POWER
FOOT
5
8
OUT
AMP IN
SWITCH
9
10
11
1
12
I n s p i r e d b y M i c h a e l L a n d a u
for connections. Both PREAMP OUT and
the
ON
ON
STANDBY
OFF
FENDER MUSICAL INSTRUMENTS CORP.
ASSY. P/N 7705958000
VOLUME
BOOST
9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pr 247

Tabla de contenido