Lcd Display - Numark iCDX Manual De Referencia

8.
SCRATCH - Turns scratch mode on or off. If
scratch mode is on, the button will light up
and the center part of the jog wheel will
scratch like a turntable when you spin it. If
scratch mode is off, the center part of the
jog wheel will pitch bend when you spin it.
9.
TAP - Pressing this button in time with the
beat will help the built in BPM counter detect
the proper tempo. Holding the button for 2
seconds will cause the BPM counter to reset
and recalculate.
10.
WET / DRY FADER - Use this to adjust how
much of the effect will be mixed into the
main mix. The 0% or "dry" side of the fader
will give you less of the effected music and
more of the original music while the 100% or
"wet" side adds more of the effected music
and less of the original music.
11.
F/X - Pressing this button will turn effect
mode on or off.
illuminated, effects mode is on.
12.
F/X SELECT - Use this toggle switch to
choose which effect you want to use.
are six different effects available.
effects section in this manual for more
information.
13.
PARAMETER KNOB
multiple uses depending on what you are
doing when you turn it.
By default, spinning this knob will adjust a
parameter of the effect you have currently
chosen with the F/X SELECT switch.
more information see the effect section later
in this manual.
Other settings can be adjusted by holding
down an appropriate button while turning
the parameter knob.
14.
TIME - Toggles the display to show elapsed
time, time remaining on the current song, or
time remaining of the entire play order.
15.
PROG (Program) - Allows you to specify the
play order or "program" of the current CD.
Press PROG to enter program mode, then
use the TRACK knob to choose the first song
in your program. Press PROG again to store
that song, then select your next songs the
same way. When you are happy with your
program, press PLAY to begin playing the
songs you have selected, in the order you
chose them.
Holfing down the PROG button and turning
the PARAMETER knob will bring you to a list
of menu options.
Knob Features" section of this manual for
more information.
16.
SRC (Source) – Hold down SRC button and
turn PARAMETER knob to choose which audio
source you want to play; CD, USB, or you
can use the iCDX as a USB MIDI controller.
This button will not function if the iCDX is
currently playing.
17.
LCD DISPLAY
functions are displayed here.
available), ID3 tag information and effects
settings are all shown here.
If the FX button is
There
See the
- This knob has
For
Please see "Parameter
- All information and
CD text (if
18.
RECALL / STORE - Pressing and holding the
RECALL button for 2 seconds will allow cue
points to be stored. More than one cue set
can be stored per CD.
numbered sequentially per CD.
When a CD with stored cue points is
inserted, the display will indicate that there
are "Cue Points Available".
stored cue points press and release the
RECALL button. If more than one set of cue
points has
parameter knob will allow you to cycle
through your stored cue sets.
19.
BACK - When navigating a CD or device with
folders, this button will take you back to the
previous level (folder).
20.
(PLAY) MODE - There are four playback
modes:
Single: Plays the selected song, then
pauses and cues the next track.
SingleReplay: Repeats the current song
until manually stopped.
Random: Plays all songs on the CD in a
random order.
Continuous: Plays all songs on the CD
in order then repeats at the beginning.
21.
TRACK KNOB - Used to skip from track to
track, for folder navigation and as an "enter"
button.
22.
SHIFT - Used with the looping feature, the
shift switch allows you to cut your loop in
half or double it. If Smart Loop is on you will
be limited to a minimum length of 1 beat.
23.
LOOP IN / OUT / RELOOP - These buttons
are used to define your beginning and
ending loop points (Loop In and Loop Out) or
to replay or restart your loop (Reloop). For
more information about this feature please
see the looping section of this manual.
24.
TRIGGER BUTTONS - These buttons can be
used for 3 possible functions, chosen by
holding the REC button and turning the
Parameter knob.
the "Multi Mode Trigger Buttons" section
later in this manual.
25.
REC - This button is used in conjunction with
the 3 assignable trigger buttons (24) to
record samples and set hot start points.
When used
parameter knob, this allows you to set the
mode for
buttons (23).
26.
(BUTTON) MODE - This button is used to
change the function of the 3 assignable
buttons.
between LOOP-2, HOT CUE and SAMPLES.
27.
SEARCH - When engaged, search mode will
allow you to use the center of the jog wheel
to quickly scan through the current track. If
you do not touch the wheel for 10 seconds
you will automatically exit search mode.
Search speed can be adjusted by holding the
SEARCH button and turning the parameter
knob.
28.
PITCH FADER - This controls the speed of
the music. Moving towards the + will speed
the music up, while moving towards the "-"
will slow it down.
adjustment is shown on the display.
4
Cue sets will be
To recall your
been saved on a
For more information see
in conjunction
the three multi-mode
Pressing this button will cycle
The percentage of pitch
CD, the
with the
trigger