Fein ASCS6.3 Manual De Instrucciones página 19

OBJ_BUCH-0000000372-001.book Page 19 Thursday, February 14, 2019 10:52 AM
Before any work on the machine itself, remove the bat-
tery from the power tool. If the power tool accidentally
starts, there is danger of injury.
Remove the battery only when the power tool is
switched off.
Keep the battery away from children.
Keep the battery clean and protect it against moisture
and water. Clean contaminated battery terminals and
power tool connections with a dry, clean cloth.
Use only intact original FEIN batteries that are intended
for your power tool. When working with and charging
incorrect, damaged, repaired or reconditioned batter-
ies, imitations or other brands, there is danger of fire
and/or explosion.
Follow the safety warnings in the operating instructions
of the battery charger.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a stand-
ardised test given in EN 62841 and may be used to
compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may
differ. This may significantly increase the exposure level
over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the oper-
ator from the effects of vibration such as: maintain the
tool and the accessories, keep the hands warm, organi-
sation of work patterns.
Operating Instructions.
Adjust the rotation selector switch only when the
machine is at a complete stop.
To avoid accidental starting, e. g., during transport, set
the rotation selector switch to the centre position.
When overheated, the machine runs with short, low-
power impulses. Allow the machine to cool down at
no-load speed.
For reliable working results, always carry out screw-
driving operations using the depth stop.
Electronic torque shut-off (see pages 6 – 7).
The electronic torque shut-off can be used when work-
ing without depth stop.
Adjust the torque only when the machine is at a com-
plete stop.
The motor switches off when reaching the set torque
and an audio signal sounds. After the shut-off has taken
place, release the on/off switch and press it again for the
next screwdriving operation.
The audio signal can be switched on and off.
The electronic shut-off is deactivated when working in
the " " torque level.
To achieve good working results, press the power tool
with sufficient force against the screw.
Handling the battery.
Store, operate and charge the battery only using FEIN
battery chargers within the battery operating-tempera-
ture range between 5 °C – 45 °C (41 °F – 113 °F). At
the beginning of the charging procedure, the battery
temperature must be within the battery operating-tem-
perature range.
LED indica- Meaning
tor
1 – 4 green Percentage of
LED charge condi-
tion
Continu- Battery is
ous red almost empty
light
Red flash- Battery is not
ing light ready for
operation
The real percentage of the battery charge condition is
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor
prior to the battery being deep discharged.
Repair and customer service.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
tool. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
If required, you can change the following parts your-
self: application tools, depth stop, battery, belt clip
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the
last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH, C-D1_IA,
D-73529 Schwäbisch Gmünd
en
19
Activity
Operation
Charge battery
Bring the battery into
the battery operating-
temperature range,
then charge