Kobra 260 Instrucciones De Manejo página 5

FEATURES
KOBRA 260, 300, 385, 390 and 400 are paper shredding
machines designed tor standard sheets and EDP print-outs
shredding.
INSTALLATION
For machines with a removable plug, use an easily accessible
power socket near the machine.
KOBRA 260 (S2-S4-S5-C2-C4-HS-H86), KOBRA 300 (SS4-
SS5-CC2-CC4-HS-H56), KOBRA 385 (C2-C4) Fig. 1 and 2.
Position the shredder head on the cabinet.
Place the plastic bag (b) around the bag metal holder (c) and
insert the bag metal holder into the housing located inside
the cabinet. Press the bag metal holder until it stops against
the back of the cabinet.
KOBRA 385 S4, KOBRA 385 SS4 DESK-TOP USE (FIG. 4).
Place the KOBRA shredder on the working desk. Position the
machine with the plastic stopper feet against the desk edge
(4a).
The plastic stopper feet are automatically positioning the
machine to allow the exit of the shredded paper.
Place the plastic bag (4b) around the bag metal holder (4c)
and insert the bag metal holder into the housings located
underneath the machine.
The bag metal holder can be easily inserted into the hou-
sings by following the two arrows stamped on the machine
(4d).
Position the bag metal holder at 15-20 cm. (6-8) from the
desk edge.
KOBRA 390 (C4-S5) AND KOBRA 400 (C2-C4-S5-HS-HS6)
FIG.3
Open the front door and pull out the plastic bag holder (3c)
from the bearing mounted sliding guides (3a). Remove two
transportation Mocking bolts (lid). Place the plastic bag (3b)
around the bag metal holder (3c) and position it back on
sliding guides (3a).
Press the sliding guides inside the cabinet until they stop
and close iront door.
OPERATION -
ENERGY SMART SYSTEM
Connect the electrical plug of the machine to the main elec-
trical socket. Switch the machine on by pressing the on/off
switch (F). The green Stand-by signal (1) on the panel board
and the ENERGY SMART optical indicator (3) will illuminate.
Machine is now ready to work.
Through the electronic eyes the machine automatically
starts by inserting the documents to shred. When shredding
is completed the machine tums automatically to the stand-
by mode.
In case too much paper is inserted, machine stops automa-
tically and reverses through the electronic controls. By pres-
sing the Reverse bottom (R) the machine can be cleared of
the excess of paper.
By inserting a smaller quantity of paper the machine re-
starts shredding.
In order to get the best performances and to preserve the
life-time of the mechanical components your KOBRA shred-
der should operate below the maximum capacity avoiding
jamming situations.
ENERGY SMART System: approximately 20
after the shredding operation is completed the ENERGY
SMART management system will automatically turn the
Manuale Kobra 260, 300, 385, 390 e 400.indd 8-9
optical indicator (3) off and put the machine into a stand
by zero power consumption mode. The ENERGY SMART
management system can save up to 10 Kw of electrical
energy a year and will reduce by 65 Kgs the carbon dioxide
(C02) that would have been introduced into the atmosphere
for generation of the power saved by ENERGY SMART.
Whenever a sheet of paper is introduced into the shredder
opening, the electronic eyes (4) will automatically re-activate
all the machine's functions and the optical indicators (3) will
light up again.
KOBRA 385 models are equipped with the ENERGY SMART
system without optical indicators.
The paper shredder is delivered with a plastic flap (G). Flap
must be moved over the paper entry throat and FLOPPY
DlSKS, CDs or CREDIT CARDS should be inserted into the
dedicated slot which keeps the material to shred aligned
between the electronic eyes and protects the operator from
pieces oi plastic which could fly out from the cutting unit
during shredding.
KOBRA 385 models are not suitable for media carriers and
therefore are not equipped with the plastic flap (G).
AUTOMATIC FUNCTIONS
- Electronic eyes for automatic Start/Stop when paper to sh-
red is inserted into the machine
- AUTOMATIC STOP for bag full and/or door open (red light
(2) on panel board)
KOBRA 260 (S2-S4-S5-C2-C4-HS-HS6), KOBRA 300 (SS4-
SS5-CC2-CO4-HS-HS6), KOBRA 385 (C2-C4), KOBRA 390
(S5-C4), KOBRA 400 (S5-C2-C4-HS-HS6) are equipped with
two special sensor which automatically stop the machine in
case of bag full or door open.
Model KOBRA 385S4 and KOBRA 385854 are equipped with
only one sensor which automatically stops the machine in
case of bag full (red light (2) on panel board).
- AUTOMATIC motor protection
In case of overheating of the electrical motor an automa-
tic protection tuns the machine off. Alter a cooling time of
about 15 minutes the shredder is ready for normal opera-
tion.
- AUTOMATIC STOP in case of paper jam which stops the
machine when too much paper is inserted. By pressing the
Reverse button (B) the machine can be cleared of the excess
of paper.
- ENERGY SMART management system which automatically
turns the shredder into almost a zero power consumption of
the shredder. This function activates after 20 seconds from
last shredding operation
ATTENTl0N: when the automatic motor protection is activa-
ted the machine cannot be operated even if on main switch
board the stand-by light signal is on.
MAINTENANCE
Your KOBRA shredder does not require special maintenance.
In order to keep the cutting knives cleaned, shred from time
to time a sheet of paper with some drops of machine oil
(included only in cross-cut units). The introduction of metal
into cutting knives may affect the quality of cut and cause
damages to cutting knives.
seconds
8
ACCESSORIES
COMPUTER FORMS SHELF
Kobra shredders are designed to be used in coniuction with
a computer forms shelf (E) which allows easy shredding of
continuous computer paper.
Insert the two rear sides of the housings located on the back
side of the top cover for KOBRA 260-300-390-400 (Fig.1-3).
The shelf of KOBRA 385 can be mounted by inserting the
two sides of the shelf into the machine. Push the shelf into
the housing until it stops in its final positions as shown in
Fig. 2.
KOBRA 385 S4 and KOBRA SS4
CABINET WITH BELLOW (fig. 6)
- Installation
KOBRA is also designed to be used in conjunction with a
special cabinet which is equipped with a front sliding bel-
lovn (6a).
By positioning the machine on the cabinet as shown in Fig.
6. KOBRA becomes an attractive compact castor mounted
shredder. The plastic bag metal holder is also securing the
machine to the cabinet. When the plastic bag holder is in-
serted in its position the machine cannot be released from
the cabinet.
DECLARATION OF CONFORMITY
Compliant with: - Directive CE (2006/42/CE)
- Directive EMC (2004/108/CE)
- RoHS (2011/65/EU)
The manufacturer ELCOMAN SRL
VIA GORIZIA,9 20813 BOVISIO MASCIAGO (MB) – ITALY-
Declares herewith that the following paper shredders comply with the standards of the LDV Directive 2006/42/CE
- KOBRA series : Kobra 260 , 300 , 385 , 390 , 400
Standards applied are:
EN 60950-1 :2006/A11 :2009/A1 :2010/A12 :2011
EN 55014-1 :2006
EN 55014-2 :1997+A1 :2001
EN 61000-3-2 :2006
EN 61000-3-3 :1995+A1(2001) + A2 (2005)
EN 61000-4-2(1995)+A1(1998) + A2 (2001)
Bovisio Masciago, 31.12.13
A.DE ROSA
- Emptying the plastic bag by operating the bellow (fig. 6).
The cabinet of the KOBRA is equipped with a sliding bellow
which allows easy emptying of the plastic bag.
To open the bellow, first press down the two front handles
(6b).
To close the bellow just lift the bellow up by the two front
handles until the magnetic closing.
ATTENTION:
The bellow can be cleaned by using a soft cloth with water
and soap. Do not use anysolvent or chemicals.
CABINET WITH FRONT DOOR (STANDARD CABINET) (fig. 2).
KOBRA 385 S4 and 385 SS4 can be also used in conjuction
with a standard cabinet equipped with front door.
Place the shredder head on standard cabinet as shown in
Fig. 2. DESK MOUNTING ASSEMBLY (Fig. 5)
KOBRA can also be operated with a unique desk mounting
assembly which allows to hang the machine at a desk or at
shelf, either in the office or in the warehouse.
~ Installation
Open the desk-mounting assembly frame (5a) and position
it on the working desk or shelf as shown in fig. 5.
Insert the machine as shown in Hg. 5 and insert the plastic
bag holder with the plastic bag in place.
Operate the machine as a desk top shredder.
EN 61000-4-3(2006) ETSI EN 301 489-3 v 1.4.1 (2002-08)
EN 61000-4-4(2004) ETSI EN 301 489-1 v 1.6.1 (2005-09)
EN 61000-4-5(2006)
EN 61000-4-6(2007)
EN 61000-4-8 (1993) + A1(2001)
EN 61000-4-11 (2004)
9 Kobra Serie 260, 300, 385, 390, 400 Manuale
02/08/2017 09:46:16