Makita 9500D Manual De Instrucciones página 4

ADDITIONAL SAFETY RULES
FOR MACHINE
1. Be aware that this machine is always in an
operating condition, because it does not have
to be plugged into an electrical outlet.
2. Keep guards in place.
3. Use only wheels having a maximum operating
speed at least as high as ''No load RPM''
marked on the machine's nameplate. When
using depressed center wheels, be sure to use
only fiberglass-reinforced wheels.
4. Check the wheel carefully for cracks or dam-
age before operation. Replace cracked or
damaged wheel immediately.
5. Use only flanges specified for this machine.
6. Be careful not to damage the spindle, the
flange (especially the installing surface) or the
lock nut. Damage to these parts could result in
wheel breakage.
7. Hold the machine firmly.
8. Keep hands away from rotating parts.
9. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
10. Before using the machine on an actual work-
piece, let it run for a while. Watch for vibration
or wobbling that could indicate poor installa-
tion or a poorly balanced wheel.
11. Use the specified surface of the wheel to
perform the grinding.
12. Watch out for flying sparks. Hold the machine
so that sparks fly away from you and other
persons or flammable materials.
13. Do not leave the machine running. Operate the
machine only when hand-held.
14. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge
(Fig. 1)
• Always switch off the machine before insertion or
removal of the battery cartridge.
• To remove the battery cartridge, pull out the set
plate on the machine and grasp both sides of the
cartridge while withdrawing it from the machine.
• To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Snap the set plate back into
place. Be sure to close the set plate fully before
using the machine.
• Do not use force when inserting the battery car-
tridge. If the cartridge does not slide in easily, it is
not being inserted correctly.
4
Charging (Fig. 2)
1. Plug the battery charger into your power source.
2. Insert the battery cartridge so that the plus and
minus terminals on the battery cartridge are on the
same sides as their respective markings on the
battery charger. Insert the cartridge fully into the
port so that it rests on the charger port floor.
3. When the battery cartridge is inserted, the charg-
ing light color will flash in red color and charging
will begin.
4. When charging is completed, the charging light
goes out. The charging time is as follows:
Battery 7000, 7100, 7120, 9000, 9100, 9100A,
9120: approx. 60 minutes.
5. If you leave the battery cartridge in the charger
after the charging cycle is complete, the charger
will switch into its ''trickle charge (maintenance
charge)'' mode.
6. After charging, remove the battery cartridge from
the charger and unplug the charger from the
power source.
Battery type
7000
CAUTION:
• The battery charger is for charging Makita battery
cartridge. Never use it for other purposes or for
other manufacturer's batteries.
• When you charge a new battery cartridge or a
battery cartridge which has not been used for a long
period of time, it may not accept a full charge. This
is a normal condition and does not indicate a
problem. You can recharge the battery cartridge
fully after discharging it completely and recharging a
couple of times.
• When you charge a battery cartridge from a just-
operated machine or a battery cartridge which has
been left in a location exposed to direct sunlight or
heat for a long time, let it cool off. Then re-insert it
and try to charge it once more.
• When you charge a new battery cartridge or a
battery cartridge which has not been used for a long
period, sometimes the charging light will go out
soon. If this occurs, remove the battery cartridge
and re-insert it. If the charging light goes out within
one minute even after repeating this procedure a
couple of times, the battery cartridge is dead.
Replace it with a new one.
Trickle charge (Maintenance charge)
If you leave the battery cartridge in the charger to
prevent spontaneous discharging after full charge,
the charger will switch into its ''trickle charge (main-
tenance charge)'' mode and keep the battery car-
tridge fresh and fully charged.
Capacity Number of
(mAh) cells
1,300 6