Package Contents; Technical Data - Parkside PHSHE 900 B2 Traducción Del Manual De Instrucciones Original

Package contents

1 motor unit PHSHE 900 B2
1 hedge trimmer attachment PHS 1 (hereinafter hedge trimmer)
1 pole pruner attachment PHE 1 (hereinafter pole pruner)
Accessories
1 shoulder strap
1 chain guard
1 blade guard
1 100 ml organic chain oil
1 assembly tool
1 set of operating instructions

Technical data

Motor unit:
Rated voltage:
Rated output:
Protection class:
Weight:
(without handle &
carrying strap):
Pole pruner:
Chain speed:
Working angle:
Weight (ready for use):
Oil tank, recommended fill level: 100 ml
Cut length:
Blade:
Saw chain:
Hedge trimmer:
Idle stroke speed:
Working angle:
Cut length:
Tooth spacing:
Weight
(ready for use):
Noise and vibration information:
Measured sound value determined according to EN 60745. The A-rated
noise levels of the electrical power tool are tyoically at:
Pole pruner:
Sound pressure level:
Uncertainty K:
Sound power level:
Uncertainty K:
Hedge trimmer:
Sound pressure level:
Uncertainty K:
Sound power level:
Guaranteed sound power level:
Uncertainty K:
PHSHE 900 B2
PHSHE 900 B2
230 V ∼ 50 Hz (AC)
900 W
II / (double insulation)
approx. 2.7 kg
PHE 1
max. 6 m/s
0°; 15°; 30°
approx. 1.6 kg
approx. 260 mm
Oregon type 100SDEA041
Oregon 91P040X
PHS 1
2000 rpm
-90° to +90°
410 mm
20 mm
approx. 2.1 kg
PHE 1
L = 83 dB (A)
PA
3 dB
L = 104 dB (A)
WA
3 dB
PHS 1
L = 81 dB (A)
PA
3 dB
L = 102 dB (A)
WA
L = 105 dB (A)
WA
3 dB
Vibration values (vector total of three directions) determined in accordance
with EN 60745:
Pole pruner:
Vibration on the front handle: Vibration emission value
Vibration on the rear handle:
Hedge trimmer:
Vibration on the front handle: Vibration emission value
Vibration on the rear handle:
Wear ear protection!
NOTE
► The vibration level specified in these instructions has been measured
in accordance with the standardised measuring procedure specified
in EN 60745 and can be used to make equipment comparisons. The
specified vibration emission value can also be used to make an initial
exposure estimate.
WARNING!
► The vibration level will vary according to the use of the power tool
and may sometimes be higher than the value specified in these
instructions. Regular use of the power tool in such a way may cause
the user to underestimate the vibration. Try to keep the vibration
exposure as low as possible. Measures to reduce the vibration
exposure are, for example, wearing gloves and limiting the working
time. All states of operation must be considered (e.g. times when the
power tool is switched off and times where the power tool is switched
on but running without load).
Explanation of the symbols on the appliance:
Read the operating instructions and safety
advice before initial operation!
Wear protective gloves!
Wear safety shoes!
Wear ear protection!
Wear a hard hat!
Wear protective goggles!
a = 1.0 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
vibration emission value
a = 1.2 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
a = 1.6 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
Vibration emission value
a = 1.8 m/s 2
h,D
Uncertainty K = 1.5 m/s 2
GB │ MT │ 31 ■