Before Use; Motor Unit; Attaching The Round Handle; Assembling The Quick Release Mechanism - Parkside PHSHE 900 B2 Traducción Del Manual De Instrucciones Original

Before use

CAUTION! RISK OF INJURY!
► Before any work on the appliance, disconnect the plug.
Risk of electric shock!

Motor unit

Attaching the round handle

♦ Place the round handle in the desired position on the boom
♦ Tighten the screw .

Assembling the quick release mechanism

♦ Hook in the carabiner and secure it with the red strap on the quick
release mechanism (see figures). Pull on the red strap if you have to
put down the appliance quickly.

Fastening/attaching the shoulder strap

♦ Hook the shoulder strap into the carrying lug
♦ Adjust the length of the shoulder strap
lug is at hip height when the strap is hooked in place.

Assembling the hedge trimmer

♦ Push the front boom of the hedge trimmer onto the boom
motor unit.
♦ The locking pin must engage.
♦ Secure the two booms
the nut on the opposite side.

Mounting the pole pruner

♦ Push the front boom of the pole pruner to the boom
unit.
♦ The locking pin must click into place.
♦ Secure the two booms
the nut on the opposite side.

Swivelling of the hedge trimmer

♦ Trigger the lock/release .
♦ Press the control lever and swivel the hedge trimmer into the
desired position.
♦ Allow the control lever and the lock/release
recess in the base plate (hedge trimmer)

Swivelling of the pole pruner

♦ Release the lock/release .
♦ Press the control lever and swivel the pole pruner into the desired
position.
♦ Allow the control lever and the lock/release
recess in the base plate (pole pruner)
■ 36 │ GB │ MT
.
to your size so that the carrying
with the tommy screw ; to do this, fit
of the motor
with the tommy screw ; to do this, fit
to click into the
.
to click into the
.

Mounting the saw chain and blade

WARNING!
► Wear protective gloves! There is a danger of injury from the sharp
cutting teeth!
NOTE
► Pay close attention to the running direction of the saw chain
the blade and at the sprocket cover
.
► The blade and the saw chain
delivery.
► Depending on wear, the blade
♦ Undo the nut using the assembly tool
♦ Remove the sprocket cover
♦ You may have to loosen the saw chain
and the saw chain
chain"). Follow these instructions in reverse order.
♦ Remove the blade
(pole pruner) .
♦ Reset the saw chain
♦ Lay the guide rail
roll pin in the blade hole
over the chain sprocket
♦ Now you can tighten the saw chain
checking the saw chain").
♦ Replace the sprocket cover

Tightening and checking the saw chain

of the
NOTE
► The tension of the saw chain
function of the appliance. A correctly pre-stressed saw chain
increases the service life of your appliance.
WARNING!
► Wear protective gloves! There is a danger of injury from the sharp
cutting teeth!
♦ Loosen the nut
♦ Using the assembly tool
clockwise direction to increase the tension.
♦ Using the assembly tool
anticlockwise direction to decrease the tension.
♦ The saw chain
whether the saw chain
♦ Tighten the nut
NOTE
► When pulling on the saw chain
the gap between the saw chain
than 2 mm.
► A new saw chain
► Check the chain tension before each use of the appliance.
.
are already assembled upon
can be turned.
.
.
to remove the blade
(see section "Tightening and checking the saw
with the saw chain from the base plate
starting at the top of the blade
over the blade guide , while inserting the chain
. At the same time, lay the saw chain
.
(see section "Tightening and
and tighten the nut
is important for your safety and the
a little using the assembly tool
, turn the chain adjuster screw
, turn the chain adjuster screw
must lie against the underside of the blade. Check
can be drawn over the blade
using the assembly tool .
with a force of 9 N (approx. 1 kg),
and blade should not be more
stretches and must be tightened more frequently.
PHSHE 900 B2
on
.
gently.
.
in a
in an
by hand.