Publicidad
ALL REQUIREMENTS COVERED IN
ASTM F833 STANDARD AND LATEST
REVISIONS.
COMPONENTS OF THE ITEM
Check the contents of the packaging and if
you have any complaints please contact the
Assistance Service.
_ Duette Piroet / Triplette Piroet: chassis: 2 rear
wheels, 2 front wheels.
INSTRUCTIONS
1 FITTING THE WHEELS: With the chassis closed,
fit the front wheels by inserting them until
they click (fig_a) and then proceed similarly
with the rear wheels until they click (fig_b).
2 OPENING: activate the brake on the folded
chassis. Raise the handlebar in the direction
of the arrow (fig_a) and lock it until the final
click (fig_b).
3 BRAKE: to activate the brake on the chassis,
push down with your foot on the brake bar
located on the rear wheels, as shown by the
arrows in the figure.
4 Check that the opening is correct, as in the
figure.
5 BASKET: Insert the support tube into the
fabric loop on the back of the basket, with the
two silver buttons facing downward (fig_a).
Press the silver buttons under the metallic
tube and slide it into its seats on the back of
the chassis (fig_b).
6 IMPORTANT! Fix the three lower eyelets of
the basket to the three grey buttons located
above the rear bar. Please note that the
eyelets open (fig_a).
Fix the two upper eyelets of the basket to the
two grey buttons on the sides of the basket
tube supports. Please note that the eyelets
open (fig_b).
7 Fix the two upper eyelets of the basket to the
two grey buttons on the front supports of the
basket (fig_c). Run the two zip strips, upper
and lower, respectively over and under the
front chassis tubes (fig_d).
8 Join the zip strips together and pull the zip
shut (fig_e).
9 Fix the four side Velcro strips to the basket
tubes, as shown in the figure.
10 SWIVEL WHEELS Lower the lever to lock the
front wheels (fig_a). Move the lever in the
opposite direction to make the wheels swivel
(fig_b). The rear wheels are fixed.
11 SIDE HANDLES: the complete chassis may
be lifted using the central external handles
(fig_a) and the rear handlebar (fig_b). The
chassis must be lifted by two people.
Figure C shows the correct way to lift it.
12 WHEEL REMOVAL: To remove the rear wheels:
pull the pivot outwards and remove the wheel
as shown in the figure (fig_a).
To remove the front wheels: press the tab as
shown and remove the wheel (fig_b).
13 FOLDING: apply the brake and release the
seats.
To close the chassis, push the side button,
lift both levers on the handlebar (fig_a) and
rotate it forward (fig_b) until it closes (fig_c).
You can fold up the frame without releasing
the Pop-Up seats. To do this, lower the
backrest of both seats fully forward.
GANCIOMATIC SYSTEM
The Ganciomatic System is a fast and
convenient system that allows you to attach
the Seat Duette/Triplette, the Primo Viaggio
4.35 car seat, and the Pop-Up bassinet (sold
separately) to the frame's Ganciomatic Base
in one easy movement. Position them on
the Ganciomatic Base and press downwards
on the product with both hands until they
lock into place. Always apply the frame or
stroller brake before securing or releasing the
products (refer to the respective instruction
manuals). Follow the directions for specific
product combinations.
WARNING:
stable, we recommend always installing all
the Pop-Up seats. If for any reason you are
using the product with a single occupant,
we recommend you fasten all the seats in
any case, and make sure they are properly
docked. ENSURE THE CHILD RESTRAINT IS
PROPERLY DOCKED.
The footrest may only be raised when the
seat faces out from the frame.
14 DUETTE FRAME PIROET+ 2 SEATS DUETTE
POP-UP
Figures A, B, C and D show the positions in
which the seats may be installed.
Figure D shows the "cot" position; this is
obtained by lowering the backrest and
raising only the leg rest, keeping the footrest
lowered in the vertical position as shown in
the figure.
15 DUETTE FRAME PIROET+ SEAT DUETTE
POP-UP + POP-UP BASSINET
Figure A shows the positions in which the
products may be installed.
16 DUETTE FRAME PIROET+ 2 PRIMO
VIAGGIO 4.35 CAR SEATS Figure A shows
the positions in which the products may be
installed (facing mom).
17 DUETTE FRAME PIROET+ PRIMO VIAGGIO
4.35 CAR SEAT + SEAT DUETTE POP-UP
Figure A shows the positions in which the
products may be installed (facing mom).
- 12 -
To ensure the product is
Publicidad
