CiDRA SONARtrac GVF-100 Manual De Instalación página 221

Table of Contents
1 SCOPE .................................................................................................................................. 1-1
2 MARKINGS ............................................................................................................................ 2-1
2.1 Transmitter [TB8-xx-xx-xx-03] for use with Sensor Head [SH-xxx-xx-xA-xxx-03]: ............... 2-1
2.2 Sensor Head [SH-xxx-xx-xA-xxx-03]: ................................................................................. 2-1
2.3 Transmitter [TB8-xx-xx-xx-04]: ........................................................................................... 2-2
3 ATEX ZONE 2 SPECIAL CONDITIONS OF USE RELATED TO THE SYMBOL "X" .............. 3-1
3.1 Transient Protection ........................................................................................................... 3-1
3.2 Electrostatic Charging ........................................................................................................ 3-1
3.3 Cable Glands ..................................................................................................................... 3-1
3.4 Control Drawings ................................................................................................................ 3-1
3.5 Environment ....................................................................................................................... 3-1
4 STANDARDS ......................................................................................................................... 4-1
5 CONTROL DRAWINGS ......................................................................................................... 5-1
6 SPECIFICATIONS ................................................................................................................. 6-1
6.1 Electrical Parameters ......................................................................................................... 6-1
6.2 Maximum Surface Temperatures ....................................................................................... 6-1
7 OPERATING CONDITIONS UNDER WHICH THIS PRODUCT MAY BE SAFELY USED ..... 7-1
7.1 Scope ................................................................................................................................. 7-1
7.2 Hazardous Rating Location of Facility Where It Is To Be Installed ...................................... 7-1
7.2.1 System including TB8-xx-xx-xx-03 Transmitter ............................................................... 7-1
7.2.2 System including TB8-xx-xx-xx-04 Transmitter ............................................................... 7-1
7.3 Installation Site Ambient Temperature, Pressure, Humidity ................................................ 7-2
7.3.1 Temperature ................................................................................................................... 7-2
7.3.2 Barometric Pressure ....................................................................................................... 7-2
7.3.3 Humidity ......................................................................................................................... 7-2
7.4 Water Spray and Dust ........................................................................................................ 7-3
7.5 Explosive Gasses ............................................................................................................... 7-3
7.6 Condition of piping ............................................................................................................. 7-3
7.7 Chemical Environment ....................................................................................................... 7-4
7.8 Mains Power ...................................................................................................................... 7-4
8 SUPPLEMENTARY INSTRUCTIONS FOR SAFE ASSEMBLY AND INSTALLATION ........... 8-1
8.1 Use Control Drawing, Install Per Code ............................................................................... 8-1
8.2 Make Correct Terminal Block Connections ......................................................................... 8-1
8.3 Use Cable Glands and/or Conduit Entries .......................................................................... 8-1
8.3.1 Selection of Cable Glands .............................................................................................. 8-1
8.3.2 Selection of Conduit Fittings ........................................................................................... 8-1
8.4 Wire With Power OFF ........................................................................................................ 8-1
8.5 Wire Securely to Terminals and Route Neatly .................................................................... 8-2
8.6 No Foreign Objects ............................................................................................................ 8-2
8.7 Avoid Leaky Pipes .............................................................................................................. 8-2
8.8 Seal Sensor Head Cover .................................................................................................... 8-2
8.9 Secure The Access Panel. ................................................................................................. 8-2
9 SUPPLEMENTARY INSTRUCTIONS FOR SAFELY PUTTING INTO SERVICE ................... 9-1
9.1 Prior to Applying Power ...................................................................................................... 9-1
9.2 Apply Power ....................................................................................................................... 9-1
9.3 Perform Setup .................................................................................................................... 9-1
9.4 Verify Proper Operation ...................................................................................................... 9-1
10 SUPPLEMENTARY INSTRUCTIONS FOR SAFE USE (NORMAL OPERATION WITH NO
OPERATOR INTERVENTION) ............................................................................................ 10-1
20909-01C Rev 06 Page i