Start-Up; Inserting Batteries; Setting The Remote Control; Operating Other Loewe Devices - Loewe SoundVision Instrucciones De Manejo

Loewe SoundVision
Instructions for Use

Start-up

Inserting batteries

To insert or replace the batteries, press on the point marked with the ar-
row. While doing so, simply slide the battery compartment lid down and
remove it. Insert alkaline manganese batteries LR 03 (AAA) and ensure
the correct position of + and –. Slide the cover on again from the bottom.
➠
Do not insert rechargeable batteries in the battery compartment
of the remote control!
➠
The batteries used must not be exposed to excessive heat such as
sunlight, fi re or similar!

Setting the remote control

Other devices
You can operate various Loewe devices using the Assist remote control.
The unit buttons REC - DVD - AUDIO can be set for this.
Press the required unit button and the Stop button
simultaneously for 5 sec. until the corresponding LED
indicator light flashes twice.
Then select the two-digit unit code from the table:
Device
Loewe ViewVision 8106 H
Loewe Viewvision, Centros 21x2
Loewe ViewVision DR+ DVB-T
Loewe Auro 2216 PS/8116 DT
Loewe BluTechVision
Loewe Soundprojector 1
Loewe TV Radio digital
Loewe Mediacenter
Loewe BluTechVision Interactive
HDMI CEC Modus
Loewe AudioVision
Loewe Sound Projector SL
Apple
Apple TV
SoundBox
SoundVision
Air Speaker
MediaVision 3D
Restore defaults
The corresponding LED indicator light flashes twice.
- 29 - - 29 -
Code Factory setting
10
12
13 REC
14
15
17
19
20
DVD
21
22
24
25
26
27
28
29 AUDIO
30
35
99

Operating other Loewe devices

Using the remote control for the Loewe SoundVision
Press the button, the LED indicator lights up for about
5 seconds
Using the remote control for a Loewe TV set
Press the button, the LED indicator lights up for about
5 seconds
Using the remote control for a Loewe recorder
Press the button, the LED indicator lights up for about
5 seconds
Using the remote control for a Loewe DVD player
Press the button, the LED indicator lights up for about
5 seconds
Every time a button is pressed, the LED indicator lights up for the se-
lected operating mode to allow you to check (TV – REC – DVD – AUDIO).
Please refer to the respective operating instructions on how to operate
the individual devices.

Connecting to the mains supply

Make the required cable connections as shown in the section "Connec-
tion" (page 28). Plug the mains plug into the mains socket 220-240V,
50/60 Hz.

Switching on/off

Switch the power switch
SoundVision switches on.
Set the Assist remote control for SoundVision mode
by pressing the AUDIO button briefly.
Press the on/off button
The unit switches on.
To switch the unit into Quick-start Stand-by Mode,
press the on/off button
switches off. The LED display on the display lights up red.
➠
In Quick-start Stand-by Mode, the switch-on process
is fast, the unit not using much electricity (page
41).
To switch the unit off into Energy Saving Mode, press
the on/off button
units switches off. The LED indication on the display
does not light up.
➠
The power consumption is very low in Energy Saving
Mode (page 41). The switch-on process takes
somewhat longer.
➠
Switch the unit off if you are away for longer periods
first using the on/off button
power switch
and protects the environment.
7 to position I.
1 briefly on the unit.
1 briefly on the unit. The unit
1 on the unit for 5 seconds. The
1 and then move the
7 to position 0. That saves energy