Work Area; Personal Safety - Bosch 3814 Instrucciones De Funcionamiento

"READ ALL INSTRUCTIONS" Failure to follow the SAFETY RULES identified by BULLET (•)
WARNING
!
symbol listed BELOW and other safety precautions, may result in serious personal injury.
General Safety Rules — for all Power Tools

Work Area

• KEEP CHILDREN AWAY. Do not let visitors contact tool or
extension cord. All visitors should be kept away from work
area.
• KEEP WORK AREAS CLEAN. Cluttered areas and benches
invite accidents.
• MAKE WORKSHOP CHILDPROOF. with pad lock, master
switches, or by removing starter keys.
• AVOID DANGEROUS ENVIRONMENTS. Don't use power
tools in damp or wet locations. Keep work area well lit. Do
not expose power tools to rain. Do not use the tool in the
presence of flammable liquids or gases.

Personal Safety

• KNOW YOUR POWER TOOL. Read and understand the
owner's manual and labels affixed to the tool. Learn its
application and limitations as well as the specific potential
hazards peculiar to this tool.
• DON'T OVERREACH. Keep proper footing and balance at
all times.
• STAY ALERT. Watch what you are doing. Use common
sense. Do not operate tool when you are tired. Do not operate
while under medication or while using alcohol or other drugs.
• DRESS PROPERLY. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewelry or long hair can be
caught in moving parts. Roll long sleeves above elbows.
Rubber gloves and non skid footwear are recommended
when working outdoors.
• USE SAFETY EQUIPMENT. ALWAYS WEAR SAFETY
GOGGLES. Dust mask, safety shoes, hard hat or hearing
protection must be used for appropriate conditions. Everyday
eyeglasses only have impact resistant lenses. They are NOT
safety glasses
• GUARD AGAINST ELECTRIC SHOCK. Prevent body
contact with grounded surfaces. For example: pipes,
radiators, ranges, refrigerator enclosures.
• DISCONNECT TOOLS FROM POWER SOURCE. When not in
use, before servicing, when changing blades, bits, cutters,
etc.
• KEEP GUARDS IN PLACE. In working order, and in proper
adjustment and alignment.
• REMOVE ADJUSTING KEYS AND WRENCHES. When not in
use, before servicing, when changing blades, bits, cutters,
etc.
• AVOID ACCIDENTAL STARTING. Make sure the switch is
in the "OFF" position before plugging in tool.
• NEVER STAND ON TOOL OR ITS STAND. Serious injury
could occur if the tool is tipped or if the cutting tool is
accidentally contacted. Do not store materials on or near the
tool such that it is necessary to stand on the tool or its stand
to reach them.
• CHECK DAMAGED PARTS.Before further use of the tool, a
guard or other part that is damaged should be carefully
checked to ensure that it will operate properly and perform its
intended function. Check for alignment of moving parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should be
properly replaced.
• All repairs, electrical or mechanical, should be attempted
only by trained repairmen. Contact the nearest Bosch Service
Center, Authorized Bosch Service Station or other competent
repair service.
• THE USE OF ANY OTHER ACCESSORIES NOT
SPECIFIED IN THIS MANUAL MAY CREATE A HAZARD.
Accessories that may be suitable for one type of tool, may
become hazardous when used on an inappropriate tool.
• DON'T FORCE TOOL. It will do the job better and safer at
the rate for which it was designed.
• USE THE RIGHT TOOL. Don't force a small tool or
attachment to do the job of a heavy duty tool. Don't used tool
for purpose not intended—for example, don't use a circular
saw for cutting tree limbs or logs.
• SECURE WORK. Use clamps or a vise to hold work. It's
safer than using your hand and it frees both hands to operate
the tool.
• DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotation of the blade or cutter only.
• NEVER LEAVE TOOL RUNNING UNATTENDED. Turn power
off. Don't leave tool until it comes to a complete stop.
• USE PROPER EXTENSION CORD. Make sure your extension
cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The table on page 4
shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge.
number. The smaller the gauge, the heavier the cord.
• DO NOT ALTER OR MISUSE TOOL. These tools are
precision built. Any alteration or modification not specified is
misuse and may result in dangerous conditions.
• AVOID GASEOUS AREAS. Do not operate electric tools in
a gaseous or explosive atmosphere. Motors in these tools
normally spark, and may result in a dangerous condition.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for better and safer performance. Follow instructions for
lubricating and changing accessories. Inspect tool cords
periodically and if damaged, have repaired by authorized
service facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean and free from oil
and grease.
• Before connecting the tool to a power source (receptacle,
outlet, etc.), be sure voltage supplied is the same as that
specified on the nameplate of the tool. A power source with a
voltage greater than that specified for the tool can result in
serious injury to the user, as well as damage to the tool. If in
doubt, DO NOT PLUG IN THE TOOL. Using a power source
with a voltage less than the nameplate rating is harmful to the
motor.
"SAVE THESE INSTRUCTIONS"
-2-
Tool Use
Tool Care