Comunello CONDOR 500 Instrucciones De Uso página 15

CONTENTS
1 GENERAL PRESCRIPTIONS
1.1 Safety prescriptions
1.2 Installation prescriptions
1.3 Operating prescriptions
2 MODELS AND PRODUCTS DESCRIPTION
2.1 Description
2.2 Typical installation
3 PRODUCT TECHNICAL SPECIFICATIONS
4 INSTALLATION
4.1 Preliminary checks
4.2 Operating limits
4.3 Installing the CONDOR operator
4.3.1 Installation
4.3.2 Installation of limit stops and switches
4.3.3 Operator manual release
5 PREPARATION FOR ELECTRICAL CONNECTIONS
6 TESTING
7 PRODUCT MAINTENANCE
8 SPARE PARTS
9 DISPOSAL OF THE PRODUCT
10 WARRANTY
1 PRESCRIPTIONS
1.1 SAFETY PRESCRIPTIONS
This installation manual is addressed exclusively
to professionally skilled personnel. Read all the
instructions carefully before starting the installation
procedures. Any operations that are not expressly
set down in these instructions are to be considered
prohibited; improper use may result in damage to
the product and place persons and property at risk.
The manufacturer declines all liability for failure to
observe best practices in gate construction and
for any possible deformation that may occur during
use of the product. Store this manual in a safe place
for future reference. The design and construction
of the devices of which model CONDOR 500 is
composed and this manual are in full compliance
with statutory legislation.
In consideration of potential hazards that may arise
during the installation and use of CONDOR 500,
the installation procedures must be carried out in
full compliance with the applicable laws, standards
and regulations; namely:
1.2 INSTALLATION PRESCRIPTIONS
• Before starting the installation procedures make
sure you have any additional devices and materials
that may be required to complete the automation
system with CONDOR 500 in consideration of the
specific application.
• The automation system must not be used until the
gate has been made safe.
• Dispose of packaging materials in compliance
with local regulations.
1.3 OPERATING PRESCRIPTIONS
• No modifications can be made to any part of
the product unless specified in this manual.
Unauthorized modification of the product is
likely to lead to malfunctions. The manufacturer
declines any liability for damage caused by
unauthorized modifications.
• The parts of the automation system must never
be immersed in water or other liquids. During
the installation procedures ensure that no liquids
penetrate inside the control unit or other open
devices.
• If liquids penetrate any parts of the automation
system disconnect the electrical power supply
immediately and consult the technical service;
the use of CONDOR 500 in such conditions
may give rise to potentially hazardous situations.
• Keep all parts CONDOR 500 away from heat
sources and open flames; exposure to heat or
flames may damage the devices and cause
faults, fire, or hazardous situations.
• When the equipment remains unused for a long
time, remove the optional battery and store it
in a dry place to avoid the risk of leakage of
harmful substances.
• Connect the control unit exclusively to an electric
power supply line equipped with an efficient
protective earth conductor.
• Any operations that require the housing of
CONDOR 500 to be opened must be performed
with the control unit and the electrical power
supply disconnected; if the disconnect device
is not clearly visible from where you are working,
attach a warning notice to the effect: "WARNING
- MAINTENANCE IN PROGRESS".
• In the case of tripping of circuit breakers or
blowing of fuses, find the fault and remedy it
before resetting the circuit breaker or changing
the fuse.
• If the fault cannot be remedied using the
information given in this manual, consult the
technical service.
2 PRODUCT DESCRIPTION AND INTENDED USE
2.1 PRODUCT DESCRIPTION
Electromechanical articulated arm operator designed for mounting on deep
pillars and for single leaves up to 5 metres. Composed of an aluminium
housing and steel arm.
2.2 TYPICAL INSTALLATION
E
C
B
A
F
KEY
A CONDOR 500
B OPENING PHOTOCELLS
C CLOSING PHOTOCELLS
D FLASHING LIGHT
E KEY SELECTOR SWITCH
F LIMIT STOP
G EXTERNAL CONTROL UNIT
COMUNELLO ®Copyright 2013 - All right reserved
D
G
C
B
A
F
15