HERKULES ZKG 305 L Manual De Instrucciones página 25

Anleitung_ZKG_305_L_SPK7:_
7. Now secure the top struts (F), corner
reinforcements (D) and side part (B) as shown in
Fig. 18 – 19 using two screws (L), washers (K)
and nuts (I) for each connection.
8. Connect the two halves of the base frame so that
the bottom and top cross struts (E, F) fit into the
corresponding recesses on the side part (B) and
intermediate strut (C) (Fig. 20).
9. Bolt the bottom cross struts (E) to the second half
of the base frame as described in 5 (Fig. 21/1).
10. Bolt the top cross struts (F) to the second half of
the base frame as described in 6 (Fig. 21/2).
11. Pull the four rubber buffers (32) off the underside
of the saw (Fig. 22).
12. Place the saw on the base frame in such a way
that the holes in which the rubber buffers (32)
were located line up with the four holes on the top
of the base frame. Now place the four screws (M)
through the base frame and saw feet from
underneath and secure the saw to the base frame
using the washers (J) and nuts (I) (Fig. 23 – 25).
6.4 Final adjustment of the stop for crosscut 90°
(Fig. 1, 26 – 28)
Fasten the turntable (17) in 0° position.
Undo the securing screw (22) and tilt the machine
head (4) as far to the right as possible using the
handle (1).
Place the 90° angular stop (a) between the saw
blade (7) and the turntable (17).
Undo the counter nut (36) and adjust the
adjustment screw (38) until the angle between the
saw blade (7) and the turntable (17) is 90°.
Retighten the counter nut (36) to secure this
setting.
Finally check the position of the pointer (20) on
the scale (19). If necessary undo the pointer (20)
with a Philips screwdriver, set it to the 0° position
on the scale (19) and tighten the retaining screw
again.
An angular stop is not supplied.
6.5 Final adjustment of the stop for meter cut 45°
(Fig. 1, 26, 29 – 30)
Fasten the turntable (17) in 0° position.
Undo the securing screw (22) and tilt the machine
head (4) to the right to an angle of 45° using the
handle (1).
Place the 45° stop angle (b) between the blade
(7) and the turntable (17).
Adjust the adjustment screw (37) until the angle
between the saw blade (7) and the turntable (17)
is 45°.
An angular stop is not supplied.
28.08.2008 10:48 Uhr Seite 25
7. Operation
7.1 Crosscut 90° and turntable 0° (Fig. 1 – 3, 31)
For cutting widths up to 100 mm it is possible to fix
the saw's drag function in its rear position with the
fixing screw for drag guide (25). If the cutting width
exceeds 100 mm you must ensure that the fixing
screw for the drag guide (25) is undone and that the
machine head (4) can be moved.
Move the machine head (4) to its upper position.
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
Place the piece of wood to be cut at the stop rail
(11) and on the turntable (17).
Lock the material with the clamping device (8) on
the fixed saw bench (18) to prevent the material
from moving during the cutting operation.
Push down the release lever (3) to release the
machine head (4).
Press the ON/OFF switch (2) to start the motor.
If the drag guide (25) is fixed: Move the machine
head (4) downwards evenly and with gentle
pressure using the handle (1) until the saw blade
(7) has cut through the workpiece.
If the drag guide (25) is not fixed:
Pull the machine head (4) as far as possible
forwards and then lower it evenly and with gently
pressure using the handle (1). Now push the
machine head (4) slowly and evenly right to the
rear until the saw blade (7) has cut right through
the workpiece.
When the cutting operation is completed, move
the machine head (4) back to its upper (home)
position and release the ON/OFF button (2).
Important. The integral resetting springs will
automatically lift the machine head. Do not simply let
go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counterpressure as it does so.
7.2 Crosscut 90° and turntable 0° - 45°
(Fig. 1 – 3, 32)
The crosscut saw can be used to make angular cuts
of 0°- 52° to the left and 0 – 60° to the right relative to
the stop rail.
Release the turntable (17) by slackening the
locking grip (14).
Press the locking lever (13), turn the turntable (17)
and scale pointer (15) to the desired angular
setting on the dial (16) and lock into place with
the locking grip (14). The saw has locking
positions at angular positions of -45°, -30°, -22,5°,
-15°, 0°, 15°, 22,5°, 30°, 45° and 60° at which the
locking lever can be engaged.
Retighten the locking grip (14) to secure the
GB
25