Hoover Sprint Evo SE71_SE41011 Manual De Instrucciones página 4

GETTING TO KNOW YOUR CLEANER
A. Cleaner main body
B. Dust Container
C. Dust Container Handle
D. Dust Container Release Button
E. Cleaner Handle
F. On/Off Button
G. Cord Rewind Button
H. Nozzle Parking Slot
I. Exhaust Filter Cover
J. Hose
K. Hose Release Button
L. Hose Handle
M. Suction Regulator*
N. Standard Tube*
O. Telescopic Tube*
P. Telescopic Tube Adjuster*
Q. Carpet and Floor nozzle(GP)**
Q1. Carpet Nozzle (CA)**
Q2. Hard Floor Nozzle (HF)**
R. Floor Type Selector Pedal**
S. Pre-motor Filter and Protective Mesh
T. Exhaust Filter
U. 2 in 1 Tool (Crevice Tool/Dusting Brush)
V. Pet Hair Remover Mini Turbo Nozzle*
W. Allergen Remover Mini Turbo Nozzle*
X. Parquet Nozzle*
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position. To
release the hose: simply press the two hose release buttons on the hose end and pull it
out. [2]
2. Connect the hose handle to the telescopic tube* upper end. [3]
3. Connect the telescopic tube* lower end to the carpet and floor nozzle**. [4]
*Certain Models Only ** Certain models only, nozzles may vary according to model
USING YOUR CLEANER
1. Extract power cord and plug it into the power supply. [5] Do not pull the cord beyond the
red marker.
2. Adjust the telescopic tube* to the desired height by moving the telescopic tube adjuster up
and raise or lower the handle to the most comfortable cleaning position. [6]
3. Carpet & Floor Nozzle**. Press the floor type selector pedal on the nozzle [7] to select the
ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
4. Switch the cleaner on by pressing the On/Off button on the cleaner main body. [8]
5. Vary the suction as desired by closing or opening the suction regulator* on the hose
handle. [9]
6. Switch off at the end of use by pressing the On/Off button. [8] Unplug and press the cord
rewind button to wind the power cord back into the cleaner. [10]
7. To store your cleaner, park the nozzle in the parking slot at the rear of the cleaner main
body. [11]
ACCESSORIES
To obtain the best performance and efficiency it is recommended that the correct nozzles
are used for the main cleaning operations. These nozzles are indicated in the diagrams by the
letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended for
occasional use only.
All accessories can be fitted to the hose handle or the end of the tubes.
2 in 1 Tool combines several functions into one tool:
Crevice Tool – For corners and hard to reach areas. [12]
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. [13]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs
removal. [1X]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen
removal. [1Y]
Parquet Nozzle* – For parquet floors and other delicate floors. [1Z]
IMPORTANT: Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.
2
*Certain Models Only ** Certain models only, nozzles may vary according to model
GB