Before Use; Safety Instructions - JB Systems Light LP-8115 Manual De Instrucciones

ENGLISH
®
Thank you for buying this JB Systems product. To take full advantage of all possibilities and for your own safety, please
read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and national
guidelines. Conformity has been established and the relevant statements and documents have been deposited by the
manufacturer.
 This device has been designed to produce decorative effect lighting and is used in light show systems.
 A lightweight RGB LED projector to be used with the LED MANAGER (special DMX power supply)
 81 LEDS (Red 26pcs + Green 26pcs + Blue 29pcs) behind a sturdy 15cm x 15cm cover.
 Two beam angles available: 15° and 40°
 Can be built in any wall and/or ceiling
 Hanging bracket included for easy fixing on truss or any surface
 Very easy electrical 4-wire connection
 Low power consumption, only 10watts!
 No heat dissipation!
 Can be used in discotheques, pubs, lounges, buildings, parkings, homes, etc.

BEFORE USE

 Before you start using this unit, please check if there's no transportation damage. Should there be any, do not use the
device and consult your dealer first.
 Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to
strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not
subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by
disregarding this user manual.
 Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user manual.
Check the contents:
Check that the carton contains the following items:
 Operating instructions
 LP-8115 unit (beam angle = 15°) or LP-8140 unit (beam angle = 40°)
 Hanging bracket with 2 knobs
 2 Spring clips

SAFETY INSTRUCTIONS:

This symbol means: indoor use only.
This symbol means: Read instructions.
 To protect the environment, please try to recycle the packing material as much as possible.
 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it
into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even
cause damages.
 This unit is for indoor use only.
 Don't place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign object
enters the unit, immediately disconnect the mains power.
 Prevent use in dusty environments and clean the unit regularly.
 Keep the unit away from children.
 Inexperienced persons should not operate this device.
 Maximum save ambient temperature is 40°C. Don't use this unit at higher ambient temperatures.
 Make sure the area below the installation place is free from unwanted persons during installation and servicing.
 The electrical installation should be carried out by qualified personal only, according to the regulations for electrical
and mechanical safety in your country.
 Check that the available voltage is not higher than the one stated on the rear panel of the unit.
 Don't connect the unit to any dimmer pack.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
JB SYSTEMS
®
OPERATION MANUAL
1/20
LP-8115 & LP-8140 RGB LED PROJECTOR
ENGLISH
Important: Never look directly into the light source! Don't use the effect in the presence of persons suffering from
epilepsy.
INSTALLATION:
!! This LP-8115/LP-8140 can only be used together with the JB SYSTEMS
!!! DON'T CONNECT DIRECTLY TO 230Vac or any ordinary 24Vdc power supply !!!
When you connect the LP-8115/LP-8140 to the LED MANAGER, just connect the corresponding colors:
You can install the LP-8115 & LP-8140 in 3 ways:
1. Using the included hanging bracket to fix the LP-8115/LP-8140 with a mounting hook
2. You can build the LP-8115/LP-8140 in a mounting panel (ex. ceiling)
3. Installing the LP-8115/LP-8140 in a mounting panel USING 4 SCREWS:
1. Using the included hanging bracket:
The hanging bracket has 2 knobs and a mounting hole to fix a small mounting hook.
Before installing this unit, please take note of following information:

Make sure the area below the installation place is free from unwanted persons while
installing

The device should be well fixed, free-swinging mounting is dangerous and may not be
considered!
2. Installing the LP-8115/LP-8140 in a mounting panel USING THE SPRING CLIPS:
IMPORTANT NOTE: Before you start installing the unit, be sure to remove the hanging bracket first !
Before installing this unit, please take note of following information:

The diameter of the hole cutout has to be 125mm x 125mm

The thickness of the mounting panel (ceiling) can be up to 15mm

Make sure the area below the installation place is free from unwanted
persons while installing
How to install the unit:

Install the Spring Clips on both sides of the enclosure.

Make sure you make the electrical connections before you install the unit
in the mounting panel!

Press both Spring Clips upwards (see picture A).

Slide the armature in the 125mm x 125mm hole of the mounting panel
(ceiling).

Release the Spring Clips (see picture B).

The armature will be locked in the mounting panel (ceiling).
JB SYSTEMS
®
OPERATION MANUAL
®
LED MANAGER !!
2/20
LP-8115 & LP-8140 RGB LED PROJECTOR