Narex EPR 35-24 Instrucciones De Uso página 22

5. Always keep these Operating Instructions
together with the chain saw.
6. Only lend or give this chain saw to persons
who are familiar with its use. Also give them
these Operating Instructions.
7. You should always be in a good physical state
when working with the chain saw. Work steadily
and with concentration. Particular concentration
is necessary towards the end of your duty.
8. Never use the chain saw while under the
influence of alcohol, medication or drugs.
B) Instructions on the use of
personal protective clothing
Working with a chain saw requires special
measures with regard to protective equipment
and clothing suitable for protecting your head,
hands, feet and legs, eyes and ears.
9. Wear close fitting clothing which cannot get
caught.
10. Always wear an approved and tested safety
helmet when felling trees and removing branches.
11. Always wear safety goggles or a face guard.
12. Always wear suitable protective gloves.
13. Wear ear protection to avoid damage to your
hearing.
14. Wear safety boots.
15. We recommend that you wear leg guards.
C) Instructions on using the chain
saw safely
16. Attention! Read the Operating Instruc-
tions carefully and have yourself instructed
in the use of a chain saw before you use it
for the first time.
17. Always store your electric tools in a safe
place. Electric tools not being used should be
stored in a dry, inaccessible or locked place,
outside the reach of children.
18. Use the cable only for the intended purpose.
Never carry or suspend electric devices by the
cable. Do not use the cable to pull the plug from
the socket. Protect the cable from heat, oil and
sharp edges.
19. Check the extension cable regularly and
replace it if it gets worn or damaged. Keep the
handle dry and free of oil and grease.
20. Pull the plug from the socket when replacing
the saw chain or sword.
21. Do not leave the tool key in the ignition.
Check before switching on that the key and
adjustment tools are removed.
22. Avoid accidental starting. Do not hold your
��
finger on the switch when carrying an electric
tool that is connected to the power source.
Ensure that the switch is off when the plug is
inserted in the socket.
23. Damaged switches have to be replaced by
a customer service workshop. Do not use an
electric tool if the switch cannot be switched on
or off.
24. Caution: Only use accessories or parts that
are listed in the operating instructions. Use of
other tools and other accessories mean safety
risks for the operator.
25. Never subject the electrical chain saw to rain
and do not work in wet surroundings.
26. Check the chain saw for its proper operating
state before every use.Please pay special atten-
tion to the sword and chain.
27. Check the power cable for damage or cracks
every time before you use it. Damaged cables
must be replaced.
28. Always hold the chain saw with both hands
while working with it.
29. No other person may be within the working
range of the chain saw.
30. The chain saw must be disconnected from
the power supply before you tighten the chain,
exchange the chain or carry out any other work
on the saw. – Withdraw the plug!
31. During work breaks put the machine down in
such a manner that nobody is at risk.
32. Always use the chain cover when transporting
the chain saw.
33. When switching on the chain saw, ensure
that it is supported well and hold it firmly. The
chain and bar must be free.
34. Before you start working ensure that you are
standing firmly.
35. Withdraw the plug immediately if the power
cable is damaged or cut.
36. Never cut with the tip of the bar – the saw
may recoil ("kick-back").
37. Do not use the chain saw near combustible
gases or dust – danger of explosion.
38. The chain saw may only be connected to
socket outlets with earthing contact and tested
electrical installations. We recommend the use
of a residual-current-operated circuit-breaker.
The fuse must have a value of 16 A and must
not be used by other consumers while working
with the chain saw.
39. The cable must be winded off completely
when you use a cable drum.
40. Ensure that the power cable has no kinks
and is not damaged.