Operating Instructions; Volume Adjustment - Jensen VM9022 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATING INSTRUCTIONS

Power On / Off
Press the
/SRC button (6) (or any other button on the front
of the unit except reset), or the
/POWER button (4) on the
remote control, to turn the unit on. The buttons on the front of
the unit light up and the current mode status appears on the
TFT screen (17).
Press and hold the
button to power off the unit.The monitor
is drawn back into the main compartment.
Audible Beep Confirmation
An audible beep tone confirms each function selection. The
Beep tone can be disabled through the Setup menu.

Volume Adjustment

To increase or decrease the volume level, turn the rotary
encoder (5) on the front panel or press the VOL+/ VOL-
buttons (15, 16) on the remote control. When the volume
level reaches "0" or "40", a beep sounds, indicating that the
adjustment limit has been reached. The volume ranges from
"0" to "40". The TFT screen displays the volume level for 3
seconds.
Programmable Turn-On Volume
This feature allows the user to select a turn-on volume setting
regardless of the volume setting prior to turning the unit off.
To program a specific turn-on volume level, turn the AUDIO
control (2) to adjust the volume to the desired turn-on volume.
Push and hold the AUDIO button while the yellow speaker
icon and level indication is displayed on the screen. The unit
will beep two times to confirm your turn-on volume setting.
Mute
Press the MUTE button on the front panel (8) or remote
control (3) to mute the volume from the unit. Press the MUTE
button again to restore the volume. "MUTE" is displayed on
the screen. Adjusting the volume or using any of the audio
setup features cancels the mute function.
Line Mute
If the "MUTE" wire is connected, audio output mutes when a
telephone call is received by a cell phone.
Playing Source Selection
Press the SRC button on the front panel (6) or remote control
(8) to change between available playing sources in the
following order: RADIO, SAT, DISC, NAV, BT, iPod, SD, USB,
AUX1, AUX2 and CAMERA. The playing mode is displayed
on the TFT screen.
Auxiliary Devices
External peripheral devices can be connected to this unit via
RCA output (AUX IN 2) or the MediaLink
iPod Connector
(GEN 5 Recommended)
USB Connector (Type A)
MediaLink
3.5mm - Audio
VIDEO
LEFT
RIGHT
RCA Inputs (AUX 1)
3.5mm Left & Right
Stereo Inputs (AUX 1)
Select "AUX1" to play an auxiliary device connected via the
MediaLink RCA or 3.5mm inputs. For example, you can play
music files from a portable music player, video from a video
camera and even view photos stored on a digital camera.
No Video Signal
AUX1
E
Q
R
E
A
R
P
I
P
Stereo
PLII Music
Select "AUX2" mode to access and control auxiliary devices
connected to the "AUX IN 2" inputs on the back of the radio.
Selecting a Source while Navigating
While navigating, other sources may be selected and listened
to such as AM-FM Tuner, CD, etc. To select a source, press
the
/SRC button (6) and then select a source from the Front
Source Menu. Navigation voice prompts will be heard
automatically, although the navigation map cannot be seen.
(The selected source audio will be muted until the navigation
voice prompt command is completed, after which the source
audio will resume.)
14
Source Menu
To access the SOURCE MENU, touch the TFT screen in the
4
top left corner of the screen.
.
DISC
SOURCE MENU
DISC
RADIO
AUX 1
This menu allows you to select a source for the front or rear
zone. Touch FRONT or REAR to choose the zone for which
you would like to specify the source. (See "Multi-ZONE
01:53 PM
Operation" on page 16.)
Audio Control Menu
The Audio Control menu features a 7-band graphic equalizer,
which allows you to easily adjust your audio system to meet
the acoustical characteristics of your vehicle, which vary
depending on the type of vehicle and its measurements.
Proper setting of the Fader and Balance boosts the effects of
the cabin equalizer.
Press the AUDIO button (5) on the front panel to display the
audio menu.
FAD-BAL
+12 —
E
Q
0 —
R
E
A
R
–12 —
P
I
P
EQ:
VM9022
F
R
SD
USB
NAV
O
N
T
SAT
iPod
BT
R
E
A
OFF
R
AUX 2
CAMERA
EQ
USER
BACK
80
250
600
1k
4k
10k
16k
User

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido