Before You Begin; Important - GE 20 Serie Manual Del Propieratio E Instalacion

Ocultar thumbs Ver también para 20 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Installation
Instructions
Models 20, 22, 25
Questions? Call 800,GE,CARES (800,432,2737) or visit
our Website at:
GEAppliances,com
In Canada, call 1,800,561,3344
or Visit
our Website at:
www,geappliances,ca
BEFOREYOU BEGIN
Read these instructions
completely
and carefully.
• IMPORTANT - Save these instructions
for
local inspector's
use.
• IMPORTANT - Observe
a,governing
codes and ordinances.
• Note to Installer
- Be sure to leave these
instructions
with the Consumer.
• Note to Consumer
_ Keep these instructions
for future reference.
• Skill level-
Installation
of this appliance
requires
basic mechanical
skills.
* Completion
time-
Refrigerator
Installation
15 minutes
* Proper installation
is the responsibility
of installer.
* Product failure due to improper
installation
is not
covered
under the Warranty.
REFRIGERATORLOCATION
, Do not install the refrigerator
where the temperature
will go below 60°F (16°C) because it will not run often
enough to maintain proper temperatures.
* Install it on a floor strong enough to support it fully
loaded.
ROLLERS
[]
[]
The rollers have 3 purposes:
[]
Rollers adjust so the door closes easily when opened
about halfway.
Rollers adjust so the refrigerator is firmly positioned on
the floor and does not wobble.
Rollers allow you to move the refrigerator
away from the
wall for cleaning.
To adjust the rollers, remove the base grille by pulling it out
at the bottom.
Turn the roller adjusting screws clockwise to raise the
refrigerator, counterclockwise
to lower it, Use an adjustable
wrench (3/8" hex head bolt) or pliers,
To replace base grille, line up the clips on back of grille
between the bar and the bottom of the cabinet, Push
forward until grille snaps into place,
WATER SUPPLY TO THE ICEMAKER (on
some
models)
If the refrigerator
has an icemaker,
it will have to be
connected
to a cold water line. A GE water
supply kit is
available
at extra cost from your dealer, by visiting our
Website at OEAppliances.com
(in Canada, at
www.GEAppliances.ca),
or from Parts and Accessories,
800.626.2002.
CLEARANCES
Allow the following
clearances for ease of installation,
proper air circulation
and plumbing
and electrical
connections.
. Sides 1/8" (4 mm) • Top 1" (25 mm), Back 1" (25 mm)
A door clearance of 3/4" (19 mm) is needed for a 90 ° door
opening which provides better access to food storage area.
DOOR ALIGNMENT
After leveling, make sure that doors are even at the top.
To make the doors even, adjust the refrigerator
door.
O
Using a 5/16" socket wrench, turn the door adjusting
screw to the right to raise the door, to the left to lower
it. (A nylon plug, embedded in the threads of the pin,
prevents the pin from turning unless a wrench is used.)
O
After one or two turns of the wrench, open and close the
refrigerator compartment
door and check the alignment
at the top of the doors.
5/16" Socket
Wrench
To remove
the
I
base grille, open
the doors and
IVr_
_ I_llI I
then pull the
1_
grille straight °ut'
I
_
Raise J
10

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

22 serie25 serieGsh22jfxlbbGsh25jgddwwGsh22jsxmss

Tabla de contenido