Additional Safety Warnings; Standard Accessories - Hitachi SV 12SG Instrucciones De Manejo

Ocultar thumbs Ver también para SV 12SG:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 22

ADDITIONAL SAFETY WARNINGS

1. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Installing the sanding paper
The sanding paper must be precisely installed on the
pad, ensuring that there is ample tension (leaving no
slack). Loosely installed sanding paper could result
in unevenly sanded surfaces and/or damage to the
sanding paper itself.
5. Attaching and removing the dust bag
Prior to the sanding operation, make sure the material of
surface you are going to sand.
If the surface under sanding operation is expected to
generate harmful / toxic dusts such as lead painted
surface, make sure the dust bag or appropriate dust
extraction system is connected with dust outlet tightly.
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts generated
in sanding operation, the dust can endanger the health
of yourself and bystanders.
6. Practical operating procedures
○ Never apply water or grinding fl uid when sanding. This
could result in electrical shock.
○ Never turn the power switch ON when the sander is
contacting the surface to be sanded. This is necessary
to preclude damage to the material. The same applies
when switching the power OFF.
○ DO NOT apply excessive pressure to the sander while
sanding. Excessive-pressure may cause overload of the
motor, reduced service life of the sanding paper, and
lowered sanding or polishing effi ciency.
7. Attaching a Sponge Pad (Velcro type) or a Stick-on pad
(optional accessories)
Replace the pad only. Use the other parts without
removing them.
8. Attaching Velcro Type Sanding Paper or Stick-on Type
sanding Paper (optional accessories)
Match the sanding paper's hole with the pad's hole and
strongly push the sanding paper with the palm of your
hand to fasten it securely in place.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
SV12SG : Orbital Sander
Read all safety warnings and all instructions.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V
Rated voltage
P
Power input
n
No-load speed
0
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
Sanding paper ............................................................. 1
Dust bag ...................................................................... 1
Standard accessories are subject to change without notice.
APPLICATIONS
Finish polishing of woodwork surfaces
Sanding surfaces of woodwork or sheet metal prior to
painting, etc.
SPECIFICATIONS
Voltage (by areas) *
Power Input
No-load speed
Sanding pad size
Sanding paper size
Weight (without cord)
* Be sure to check the nameplate on product as it is subject
to change by areas.
NOTE
Due to HITACHI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Installing the sanding paper
Attaching the dust bag
Switching on and off
3
English
(110 V, 120 V, 220 V, 230 V,
240 V)
200 W*
14000 min
-1
110 mm × 100 mm
114 mm × 140 mm
1.1 kg
Figure
Page
1
101
2
101
3
101

Publicidad

Tabla de contenido
loading

Tabla de contenido