Measuring Tool Power Supply; Initial Operation - Bosch GLL Professional 3-80 C Manual Original

OBJ_BUCH-3106-001.book Page 19 Friday, June 2, 2017 10:18 AM
Line laser
Recommended batteries
Recommended chargers
1) The working range can be decreased by unfavourable environmental conditions (e.g. direct sun irradiation).
2) Shorter operating times in Bluetooth® operation and/or in conjunction with RM 3.
3) For Bluetooth® low energy devices, establishing a connection may not be possible, depending on model and operating system. Bluetooth® devices
must support the SPP profile.
4) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be significantly
weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).
5) limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.
The measuring tool can be clearly identified with the serial number 19 on the type plate.
Assembly

Measuring tool power supply

The measuring tool can either be operated with commercially
available batteries or with a Bosch lithium-ion battery pack.
Operation with Battery Pack
Note: Use of battery packs not suitable for the measuring tool
can lead to malfunctions of or cause damage to the measuring
tool.
Note: The battery pack is supplied partially charged. To en-
sure full capacity of the battery pack, completely charge the
battery pack in the battery charger before using for the first
time.
 Use only the chargers listed in the technical data. Only
these battery chargers are matched to the lithium-ion bat-
tery of your measuring tool.
The lithium-ion battery pack can be charged at any time with-
out reducing its service life. Interrupting the charging proce-
dure does not damage the battery pack.
The "Electronic Cell Protection (ECP)" protects the lithium-
ion battery pack against deep discharging. When the battery
pack is discharged, the measuring tool is switched off by a
protective circuit.
 Do not switch the measuring tool back on after it has
been switched off by the protective circuit. The battery
pack can be damaged.
To insert the charged battery pack 15, slide it into the battery
port until you feel it engage.
To remove the battery pack 15, press the unlocking buttons
13 and pull the battery pack out of the battery port 10. Do not
use force to do this.
Operation with Batteries
Alkali-manganese batteries are recommended for the meas-
uring tool.
The batteries are inserted into the battery adapter.
 The non-rechargeable battery adapter is intended only
for use in designated Bosch measuring tools and must
not be used with power tools.
Bosch Power Tools
GLL 3-80 C
GBA 10,8V ...
GBA 12V ...
except for GBA 12V 4,0 Ah
AL 11.. CV
GAL 12.. CV
To insert the batteries, slide the cover 11 of the battery
adapter into the battery port 10. Place the batteries in the
cover as shown in the illustration on the sealing cap 14. Slide
the sealing cap over the cover until you feel it click into place.
To remove the batteries 12 press the unlocking
buttons 13 of the sealing cap 14 and pull off the
sealing cap. Make sure that the batteries do not fall
out. To do so, hold the measuring tool with the bat-
tery port 10 facing upward. Remove the batteries.
To remove the inside cover 11 from the battery
port 10, reach into the cover and pull it out of the measuring
tool by applying light pressure to the side wall.
Always replace all batteries at the same time. Only use batter-
ies from one brand and with the identical capacity.
 Remove the batteries from the measuring tool when not
using it for extended periods. When storing for extended
periods, the batteries can corrode and self-discharge.
Battery Status Indicator
The battery status indicator 2 shows the charge condition of
the battery pack or batteries:
LED
Continuous lighting, green
Continuous lighting, yellow
Continuous lighting, red
No light
If the battery pack or the batteries are running low, the laser
lines will gradually become dimmer.
Immediately replace a fault battery pack or empty batteries.
Operation

Initial Operation

 Protect the measuring tool against moisture and direct
sun light.
 Do not subject the measuring tool to extreme tempera-
tures or variations in temperature. As an example, do
not leave it in vehicles for a long time. In case of large vari-
English | 19
GLL 3-80 CG
GBA 10,8V ...
GBA 12V ...
except for GBA 12V 4,0 Ah
AL 11.. CV
GAL 12.. CV
Charge Condition
100–75 %
75–35 %
35–10 %
– Battery pack defective
– Batteries empty
1 609 92A 3PX | (2.6.17)