Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
3) ROGER BEEP
When the function is active, the icon
The Roger Beep
sounds
when the PTT switch (11) on the microphone is re-
leased in order to let your correspondent speak. Historically as transceiver
is a "simplex" communication mode, it is not possible to speak and to listen
at the same time (as it is the case with a telephone). Once someone had
finished talking, he said "Roger" in order to prevent his correspondent that
it was his turn to talk. The word "Roger" has been replaced by a significant
beep. There comes "Roger beep" from.
1.
Turn on the power while pressing the UP button (12) on the microphone.
The display shows "
" and the current status on the function: OF or On.
2.
Repeat the point 1 until the display shows the desired status.
3.
Release the UP key on the microphone.
When the function is activated "BP" appears on the display.
Default ROGER BEEP is OF.
4) FREQUENCY BAND SELECTION
(Configuration: EU; PL; d; EC; U; In)
The frequency bands have to be chosen according to the country of use.
Don't use any other configuration. Some countries need a user's licence.
See table page 50.
1.
Turn on the power while pressing the F key (7). The letter corresponding to
the current configuration is blinking.
2.
In order to change the configuration, use the ROTARY knob (4) on the unit
or the UP/DN buttons (12) on the microphone.
3.
When the configuration is selected, press the F key (7) during 1 second. The
letter corresponding to the configuration is continuously displayed and a
confirmation beep sounds.
4.
At this point, confirm the selection by switching off the transceiver and then
switching it on again.
See the frequency bands table at pages 45 to 47 / configuration table
page 49.
5) RESET
Resets all user-defined settings and returns to default values.
1.
Turn on the power while pressing the EMG key (6). "
2.
Long press F knob (7) to reset. A long beep confirms that the re initialization
have been done.
3.
If no key is pressed for 5 seconds or if the PTT switch (11) is pressed, the unit
exits
RESET without change.
appears on the display.
" blinks on the display.
D) TECHNICAL CHARACTERISTICS
1) GENERAL
- Channels
- Modulation modes
- Frequency ranges
- Antenna impedance
- Power supply
- Dimensions
- Weight
- Accessories supplied
2)
TRANSMISSION
- Frequency allowance
- Carrier power
- Transmission interference
- Audio response
- Emitted power in the adj. channel : inferior to 20 μW
- Microphone sensitivity
- Drain
- Modulated signal distortion
3)
RECEPTION
- Maxi. sensitivity at 20 dB sinad
- Frequency response
- Adjacent channel selectivity
- Maximum audio power
- Squelch sensitivity
- Frequency image rejection rate
- Intermediate frequency rej. rate
- Drain
E) TROUBLE SHOOTING
1) YOUR RADIO WILL NOT TRANSMIT OR YOUR TRANSMISSION
IS OF POOR QUALITY
-
Check that the antenna is correctly connected and that the SWR is properly
adjusted.
31
: 40
: AM / FM
: from 26.965 MHz to 27.405 MHz
: 50 ohms
: 13.2 V / 26.4 V
: 115 (L) x 165 (P) x 35 (H) mm
: 0.571 kg
: 1 microphone electret UP/DOWN with
support, mounting cradle, screws and
fused power cord.
: +/- 200 Hz
: 4 W AM / 4 W FM
: inferior to 4 nW (- 54 dBm)
: 300 Hz to 3 KHz in AM/FM
: 3.0 mV
: < 2 A max. with modulation (13.2 V)
< 1 A max. with modulation (26.4 V)
: 2 %
: 0.5 μV - 113 dBm (AM)
0.35 μV - 116 dBm (FM)
: 300 Hz to 3 kHz in AM/FM
: 60 dB
: 3 W
: minimum 0.2 μV - 120 dBm
maximum 1 mV - 47 dBm
: 60 dB
: 70 dB
: 180 ~ 500 mA maximum (13.2 V)
90 ~ 250 mA maximum (26.4 V)
Publicidad
Tabla de contenido
