Additional Safety Warnings; Standard Accessories - HIKOKI SB 8V2 Instrucciones De Manejo

h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
BELT SANDER SAFETY WARNINGS
1. Hold the power tool by insulated gripping surfaces,
because the sanding surface may contact its own
cord. Cutting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator
an electric shock.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Prior to the sanding operation, make sure the material
you are going to sand.
If generation of harmful / toxic dusts such as lead paint,
woods and metals is expected under the sanding
operation, make sure the dust bag or appropriate dust
extraction system is connected with dust outlet tightly.
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts generated
in sanding operation, the dust can endanger the health
of yourself and bystanders.
5. Sanding belt installed in the wrong direction will lower
work effi ciency and shorten life of sanding belt.
6. If sanding belt moves during operation, adjustment can
be made while in operation.
7. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
SB8V2: Belt Sander
To reduce the risk of injury, user must read
instruction manual.
Always wear eye protection.
Always wear hearing protection.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2012/19/
EU on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V
Rated voltage
P
Power Input
n
No–load belt speed
0
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
○ Endless sanding belt (Grain size: #80) .........................1
○ Dust bag ......................................................................1
○ Dust collection adapter ................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Finish sanding and fi nish fl ooring of woodwork products.
○ Base polishing of wood-coated surfaces.
○ Finish sanding of metal surfaces.
○ Base polishing of metal-coated surfaces, rust removal,
or paint removal prior to refi nishing.
○ Surface fi nishing of slate, concrete, and similar materials.
SPECIFICATIONS
Voltage (by areas)*
Power input*
No–load belt speed
Sanding belt size
Weight (without cord)**
* Be sure to check the nameplate on product as it is subject
to change by areas.
** According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
3
English
(110 V, 230 V)
1020 W
250 – 450 m/min
76 × 533 mm
4.5 kg