Exiting The System Setup Menu - Jensen UV9 Manual De Instrucciones

Audio Sub-menu Features
Setting Options Function
DRC Off Employ the Dynamic Range
Control for better playback for
On
low volumes.
Loudness Off Turn bass boost on/off
On
Subwoofer Off Turn the subwoofer on/off.
On
Sub Filter 80Hz Selecting a crossover fre-
quency sets a cut-off frequency
100Hz
of the subwoofer's LPF (low-
pass filter).
120Hz
Demo Sub-Menu Features
You can stop/run demonstration mode or turn Demo Auto
Run on/off by chooing the "Demo" option from the SETUP
MENU.
When "Demo Auto Run" is Off, you can select "Demo Mode >
Run" to start Demo Mode. Demo Mode scrolls through the
various source screens, simulating activity on the display.
"Demo Mode" is discreetly displayed in yellow text (below the
clock), to indicate the unit is in Demo Mode. To stop Demo
Mode, press the upper-left quadrant of the TFT (Source
select).
When "Demo Auto Run" is On, the unit will automatically
display Demo Mode when powered on.
Rating Sub-menu Features
The DVD system has a built-in parental lock feature to
prevent unauthorized persons from viewing restricted disc
content. By default, the rating system is unlocked. Once
setup, the parental lock is released only by entering the
correct password. Once the password is entered, rating is
available for setup.
Setting Options Function
Password _ _ _ _ Enter a 4-digit password to
activate the "Rating" feature.
Setting Options Function
Rating 1. Kid Safe Select the appropriate rating
level for the intended audience.
2. G
You may override higher rat-
3. PG
ings by using your password.
4. PG-13
5. PG-R
6. R
7. NC-17
8. Adult
Load Fac- Reset Select "Reset" to restore the
tory factory default settings for the
Rating system only.
To reset the password, access the "RATING" menu and enter
the current password. Once the correct password is entered,
you can access the "Password" field and enter a new one.
NOTE: Record the password and keep it in a safe place
for future reference. The rating for each disc is marked
on the disc, disc packing, or documentation. If the rating
is not available on the disc, the parental lock feature is
unavailable. Some discs restrict only portions of the disc
and the appropriate content will play. For details, please
refer to the disc description.
Hardware Sub-menu Features
If the rear-view video camera is connected, the unit is on, and
the TFT monitor is retracted inside the unit, the TFT monitor
automatically moves into the viewing position and Camera
mode is selected upon shifting into REVERSE gear. When
shifting into DRIVE gear, the TFT monitor is retracted back
inside unit.
Setting Options Function
Camera In Normal
Mirror Reverse the camera image as
if looking through a rear-view
mirror.
TFT Auto On The TFT panel automatically
Open opens when the unit is turned
on.
Off You must press the OPEN but-
ton (1) to open the TFT panel.
Manual When the ignition is turned
OFF, the TFT panel DOES
NOT retract if it was previously
out
12
Setting Options Function
Video Input NTSC The color signals are output in
(Input cir- the standard NTSC format.
cuitry auto-
PAL The color signals are output in
detects the
the standard PAL format.
video sig-
nal from the
Auto The color signal output is
Aux In
switched automatically based
source).
on the current video input sig-
nal - NTSC or PAL.
If the monitor is in display mode, the monitor automatically
switches to CAMERA mode upon reverse driving. When the
reverse driving stops, the monitor return to its original input
mode.
P.VOL Sub-menu Features
Setting Options Function
Source Radio Choose a source for which you
would like to increase the rela-
Disc
tive volume (LEVEL).
USB
Aux In
Navi
Level 0-6 Increase relative volume for
specified source up to 6 deci-
bels.
TS Cal (Screen Calibration)
To access the "Screen Calibration" function from the SETUP
menu, select the "TS CAL" option.
After entering calibration mode, a crosshair
corner quadrant of the screen. To begin calibration, press and
hold the crosshair for one second until it moves to the next
quadrant. Continue for each quadrant until the calibration is
completed.

Exiting the System Setup Menu

To exit setup mode and resume normal playback, press the
SETUP button (29) on the remote control or touch the BACK
button on the screen.
UV9
appears in a