Asp (Audio Sound Processing) Config Menu; Screen Calibration; Exiting The System Setup Menu - Jensen VM9311TS Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

1.
Press and hold the DISP button (5) until the clock
flashes in the LCD display.
1.
Press the /\ or V buttons (18, 19) on the joystick to move
the cursor to the "Hour" or "Min" position.
2.
Press the < or > buttons (16, 17) on the joystick to adjust
the hour or minutes.
3.
Press the DISP button (5) on the unit to confirm setup.
Returning to the System Setup Menu
To return to the System Setup menu, move to "BACK", then
press the >/|| button (18) on the remote control.
ASP (Audio Sound Processing) Config
Menu
The ASP Config Menu allows you to make fine audio
adjustments.
Accessing the ASP Config Menu
To access the "ASP CONFIG" Menu from the "SYSTEM
SETUP" menu, press the direction buttons on the joystick
(16, 17, 18, 19) or remote control (14, 17, 18, 19, 22) to
highlight "ASP CONFIG" in green. Press the >/|| button (18)
on the remote control to enter the "ASP CONFIG" menu. A
menu appears with the option for the first item, "Bass Center
Freq", highlighted in light blue.
ASP CONFIG
60Hz
15kHz
Sub Filter
80Hz
Sub Phase
0D
1.5
Adjusting a Feature
1.
Enter the option field for the feature you want to adjust
by pressing the >/|| button (18) on the remote or by
pressing the ENTER (joystick) button (20) on the unit. A
submenu appears in a second row with the selected
option highlighted in light blue.
2.
Select a new value by pressing the >> or
22) on the remote control or the /\ or V buttons (18, 19)
on the joystick.
3.
Confirm your selection by pressing the
buttons (22, 17, 19) on the remote control, or the < or >
button (16, 17) on the joystick. The new value is
highlighted in light blue and setup is complete.
Table 6: ASP Config Menu Features
Setting
Options
Bass Center
60Hz
Freq
80Hz
100Hz
130Hz
150Hz
200Hz
Treble Center
10KHz
Freq
12.5KHz
15KHz
17KHz
Sub.W Filter
80Hz
120Hz
160Hz
Sub.W Phase
0D
180D
BACK
Bass Q-Factor
1.0
1.25
1.5
2.0
BACK

Screen Calibration

To access the "Screen Calibration" function from the
SYSTEM SETUP menu, press "SCREEN CAL".
After entering calibration mode, a crosshair
corner quadrant of the screen. To begin calibration, press and
hold the crosshair for one second until it moves to the next
quadrant. Continue for each quadrant until the calibration is
completed.

Exiting the System Setup Menu

buttons (14,
<<
To exit setup mode and resume normal playback, press the
SYS SETUP button (31) on the remote control or the DISP
button (5) on the front panel.
, |<<, or >>|
<<
Function
According to the audio source, select
the Bass Center Frequency to
achieve the best Bass effect.
According to the audio source, select
the Treble Center Frequency to
achieve the best Treble effect.
Selecting a crossover frequency sets
a cut-off frequency of the subwoofer's
LPF (low-pass filter) and the
"SMALL" speakers' HPF (high-pass
filter). The Crossover frequency set-
ting has no effect if the subwoofer is
set to "OFF" and any other speaker is
set to "LARGE".
Subwoofer output IN phase
Subwoofer output OUT OF phase
NOTE: Depending on your installa-
tion, reversing the subwoofer phase
may increase Bass output.
When the Bass Center Frequency is
selected, adjusting the Bass Q-Fac-
tor alters the sharpness of the Bass
output.
Return to previous menu.
appears in a
14
VM9311TS

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido