Safety Information; Important Safety Instructions - Furman PL-8 Manual Del Propietário

SAFETY INFORMATION

To obtain best results from your Furman Classic Series power condi+oner, please read this manual carefully before using.
WARNING
To reduce the risk of electrical shock, do not expose this equipment to rain or moisture. Dangerous high voltages are present inside
the enclosure. Do not remove the cover. Refer servicing to qualified personnel only. The lightning flash with an arrowhead symbol
is intended to alert the user to the presence of uninsulated, dangerous voltage within the product's enclosure that may be of
sufficient magnitude to cons+tute a risk of electric shock.

IMPORTANT SAFETY INSTRUCTIONS

(Please read prior to installa+on)
1. Please read and observe all safety and opera+ng instruc+ons before installing your Furman Classic Series power condi+oner.
Retain these instruc+ons for future reference.
2. Your Classic Series condi+oner should not be used near water – for example, near a bathtub, washbowl, kitchen sink, laundry tub,
in a wet basement, or near a swimming pool.
3. Do not place your Classic Series condi+oner near high heat sources such as radiators, heat registers, stoves, or other appliances
that produce extreme heat.
4. The Furman PL‐8 C should only be connected to a 120 VAC, 50Hz/60Hz, 15 amp grounded electrical outlet. Do not defeat the
ground or change polariza+on of the power plug.
5. Route the AC power cord and other cables so that they are not likely to be walked on, tripped over, or stressed. Pay par+cular
aVen+on to the condi+on of the cords and cables at the plugs and at the point where they exit your Furman condi+oner. To
prevent risk of fire or injury, damaged cords and cables should be replaced immediately.
6. Clean your Furman condi+oner with a damp cloth only. Do not use solvents or abrasive cleaners. Never pour liquid on or into the
unit.
7. Your Furman condi+oner should be serviced by qualified service personnel when:
• The power supply cord or the plug has been frayed, kinked, or cut.
• Objects have fallen or liquid has been spilled into the unit.
• The unit has been exposed to rain or extreme moisture.
• The unit does not appear to operate normally.
• The "ProtecBon OK" indicator is not lit.
• The unit has been dropped, or the enclosure has been damaged.
• The retractable LED lights have failed.
8. Your Furman condi+oner requires that a safety ground be present for proper opera+on. Any aVempt to operate the unit without
a safety ground is considered improper opera+on and could invalidate the warranty.
9. Do not aVempt to service your Furman condi+oner beyond what is described in this manual. All other servicing should be
referred to qualified service personnel.
OPERATION
RETRACTABLE SMOOTH TRACK RACK LIGHTS, REAR PANEL LAMP AND DIMMER CONTROL:
The Furman Classic Series power condi+oners u+lize a dimmer control for the two retractable Smooth Track light tubes. The dim‐
mer knob controls the brightness of both front panel lamps. Turn it clockwise to increase brightness; turn it counterclockwise to
decrease brightness. The knob is also a momentary power switch for the lamps: push it in to turn the lamps on or off. When the
lamps are not in use, we recommend turning the dimmer fully counterclockwise, or pushing the knob to the off seong to maximize
the life of the LED's. Whether the light tubes are fully extended or flush with the front panel, there will be no appreciable heat
regardless of the dimmer seong due to the efficiency of our full light spectrum LED's.
All Furman Classic Series Condi+oners feature a rear rack BNC socket which will accept any 12 VAC (0.5A) gooseneck lamp assembly
(such as the Furman GN‐LED or GN‐I). Simply slide the BNC plug over the socket and rotate clockwise un+l the connector snaps into
the locked posi+on. The rear rack lamp can be powered on or off with the rear light switch which is adjacent to the BNC connector.
5