Husqvarna Connect; Operation - Husqvarna LC 151 Manual De Usuario

Ocultar thumbs Ver también para LC 151:
Tabla de contenido

Publicidad

To set the product in transport position
1. Loosen the lower knobs.
2. Move the knobs to the lower end of the grooves on
the left and the right side of the product. (Fig. 16)
3. Fold the handle forward. (Fig. 18)
To set the product in operation position
1. Fold the handle to upright position. (Fig. 19)
2. Move the knobs up in the direction of the handle until
they stop and you hear a click. (Fig. 17)
Introduction
WARNING: Before you operate the product,
you must read and understand the safety
chapter.

Husqvarna Connect

Husqvarna Connect is a free app for your mobile device.
The Husqvarna Connect app gives extended functions
for your Husqvarna product:
Extended product information.
Information about, and help with, product parts and
servicing.
To start to use Husqvarna Connect
1. Download the Husqvarna Connect app on your
mobile device.
2. Register in the Husqvarna Connect app.
3. Do the instruction steps in the Husqvarna Connect
app to connect and register the product.
Before you operate the product
1. Read the operator's manual carefully and make sure
that you understand the instructions.
2. Examine the cutting equipment to make sure that it
is correctly attached and adjusted. See
the cutting equipment on page 12 .
3. Fill the fuel tank. See
4. Fill the oil tank and do a check of the oil level. See
To do a check of the oil level on page 13 .
To fill fuel
If available, use low-emission/alkylate gasoline. If low-
emission/alkylate gasoline is not available, use good
quality unleaded gasoline or leaded gasoline with octane
number not less than 90.
CAUTION: Do not use gasoline with an
octane number less than 90 RON (87 AKI).
This can cause damage to the product.
10
To examine
To fill fuel on page 10 .
3. Tighten the knobs fully.
To assemble the grass catcher (LC
151, LC 151S)
1. Attach the grass catcher frame to the grass bag with
the rigid part of the bag on the bottom. Keep the
handle of the frame out of the top of the bag. (Fig.
20)
2. Attach the grass bag to the frame with the clips. (Fig.
21)

Operation

1. Open the fuel tank cap slowly to release the
pressure.
2. Fill slowly with a fuel can. If you spill fuel, remove it
with a cloth and let remaining fuel dry off. (Fig. 22)
3. Clean the area around the fuel tank cap.
4. Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
5. Move the product a minimum of 3 m (10 ft) from the
position where you filled the tank before a start.
To set the cutting height
1. Move the cutting height lever rearward to increase
the cutting height.
2. Move the cutting height lever forward to decrease
the cutting height. (Fig. 23)
CAUTION: Do not set the cutting height too
low. The blades can hit the ground if the
surface of the lawn is not level.
To start the product
1. Make sure that the ignition cable is connected to the
spark plug.
2. Stay behind the product.
3. Hold the engine brake handle against the handlebar.
(Fig. 24)
4. Hold the starter rope handle with your right hand.
5. Slowly pull out the starter rope until you feel some
resistance.
6. Pull with force to start the engine.
WARNING: Do not twist the starter rope
around your hand.
To use the drive on the wheels LC
151S, LB 256SP
Push the drive bail in the direction of the handlebar.
(Fig. 25)
1566 - 001 - 16.09.2020

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Lc 151sLb 256sp

Tabla de contenido