Additional Safety Rules - Panasonic EY7430 Manual De Instrucciones

Model No: EY7430 & EY7530
EN
Original instructions: English
Translation of the original instructions:
Other languages
Read the Safety Instructions booklet
and the following before using.
I. ADDITIONAL SAFETY RULES
1) Wear ear protectors.
Exposure to noise can cause hearing loss.
2) Hold power tools by insulated gripping
surfaces when performing an operation
where the cutting tool may contact
hidden wiring; contact with a "live" wire
will make exposed metal parts of the tool
"live" and shock the operator.
3) Wear a dust mask, if the work causes dust.
4) Be aware that this tool is always in an
operating condition, since it does not have
to be plugged into an electrical outlet.
5) When drilling or driving into walls,
floors, etc., "live" electrical wires may
be encountered. DO NOT TOUCH THE
CHUCK OR ANY FRONT METAL PARTS
OF THE TOOL! Hold the tool only by the
plastic handle to prevent electric shock in
case you drill or drive into a "live" wire.
6) If the bit becomes jammed, immediately
turn the trigger switch off to prevent an
overload, which can damage the battery
pack or motor.
Use reverse motion to loosen jammed bits.
7) Do NOT operate the Forward/Reverse
lever when the trigger switch is on.
The battery will discharge rapidly and
damage to the unit may occur.
8) During charging, the charger may become
slightly warm. This is normal.
Do NOT charge the battery for a long
period.
9) When storing or carrying the tool, set
the Forward/Reverse lever to the center
position (switch lock).
10) Do not strain the tool by holding the speed
control trigger halfway (speed control
mode) so that the motor stops.
11) Do not operate the speed selector switch
[1 (LOW)- 2 (HIGH)] while pulling on the
speed control trigger. This can cause the
rechargeable battery to wear quickly or
damage the internal mechanism of the
motor.
12) To prevent injury during use, hold the tool
steady at all times and avoid waving it
around.
EY7530_7430_3732_0L32_02(Eng).indd
- 8 -
8
13) Make certain that there are no hidden gas
or water pipes, or electrical wires in the
area where you will be working. Coming
into contact with hidden pipes or wires
could result in electric shock, or water or
gas leaks.
14) Make sure to hold the object you are
working on steady.
15) Ensure that the area where you will be
working is well-lit.
16) Avoid unexpected starts by keeping your
finger off the trigger switch while moving
the tool, and making sure the tool is
switched off before inserting the battery
pack.
17) Be sure to remove adjusting keys and
wrenches.
• Make certain that adjusting keys,
wrenches, and other tools have been
removed before turning the tool on.
18) Always stay focused and exercise caution
during operation.
• When operating cordless tools, always
remember the proper way to use them,
pay attention to your surroundings, and
exercise caution.
• Use common sense.
• Do not operate the tool when tired.
19) Check for damaged parts.
• Check thoroughly for damage to the
protective cover and other parts before
operating.
• Check to make sure the tool and all of its
functions are working properly.
• Check the adjustment of all movable
parts, and check all fixed parts to make
sure they are fitted properly and free of
damage. Check all parts of the tool for
abnormal function.
20) When attempting to repair the protective
cover or other parts, please follow the
instructions in the user manual. In cases
where there are no instructions in the
manual, please take it back to the store to
have it repaired.
• If the drill fails to start when the trigger
switch is held down or fails to stop when
the trigger switch is released, please
remove the battery and stop using it.
21) If the tool gets exceptionally hot during
use, please take it in for service and repair.
22) It is very important to take the tool back to
the store for repairs. Someone without the
proper knowledge and experience is not
only unprepared to carry out repairs, there
is also a risk that he or she will be injured.
23) To avoid potential injury, keep face and
2014/08/18 15:40:50