Electronic Control Set-Up Instructions - Sears Kenmore 11091942710 Instrucciones De Instalación

NOTE: After the dryer has been installed and plugged in, the
display will show "0 MINUTES." After the door has been opened
and closed, the display will show the vend price.
General User Information
SCROLLING "OUT OF ORDER" MESSAGE, FOLLOWED BY
A FAILURE OR DIAGNOSTIC CODE, SHOWING IN DISPLAY –
This condition indicates the dryer is inoperative.
"0 MINUTES" SHOWING IN DISPLAY – This indicates the
dryer cannot be operated. Coins dropped or debit inputs during
this condition will be stored in escrow but cannot be used until
normal operation is restored by opening and closing the door. If
a door switch has failed, causing "0 MINUTES" to remain in the
display after the door is opened and closed, it must be replaced
before normal operation can be restored.
COLD START (Initial first use) – Dryer is programmed at the
factory as follows: $1.50 dry price (30 minutes).
WARM START (after power failure) – A few seconds after
power is restored, if a cycle was in progress at the time of
thepowerfailure,"RESELECTCYCLE"willflashinthedisplay,
indicating the need for a fabric setting button to be pressed
to restart dryer.
PRICING – After the door is opened and then closed
following the completion of a cycle, the display indicates the
cycle price (unless set for free operation, where the display will
flash"SelectCycle").Ascoinsaredroppedordebitinputsarrive,
the display will change to lead the user through the initiation of
a cycle.
There are four (4) types of dryer pricing:
Fixed "Vend" Pricing
A dryer setup for "Fixed Cycle" operation can only accept
additional time accumulated by increments equal to the length
of a complete dry cycle. A maximum of 99 minutes may be
purchased; no additional credit is given for coins dropped
with 99 minutes in the display.
Accumulator Pricing
If option d is set to d. 00, and the 6 code is set to one
coin1,thenaccumulatorpricingisineffect.Cycletime
can be purchased one coin at a time up to the maximum
time of 99 minutes.

ELECTRONIC CONTROL SET-UP INSTRUCTIONS

PRICE
Fixed Cycle With Top Off Pricing (available for use with coin
drops or tcard readers only)
Adryersettooffer"TopOff"capabilitywillallowtimeto
be added to an existing dry cycle in increments equal to
the number of minutes of dry time per quarter (coin 1), up to
99 minutes, regardless of the cost required to start the dryer. No
credit is given for coins or debit inputs entered when the control
is displaying 99 minutes.
FREE CYCLES – This is established by setting the cycle price to
zero. When this happens, "SELECT CYCLE" will appear rather
than a cycle price. Any cycle started as a free cycle
will automatically terminate when the door is opened.
DEBIT CARD READY – This dryer is debit card ready.
It will accept a variety of debit card systems, but does NOT
come with a debit card reader. Refer to the debit card reader
manufacturer for proper dryer setup. When a Generation 2 card
reader is installed, the dryer is placed in enhanced debit mode.
InEnhancedDebitMode,thetopoffpricecanbeset
independently(seeVALUEOFCOIN2),andthetopofftime
is calculated according to the following equation:
 topoffprice
full cycle price
In models converted to a Generation 1 debit card system,
debit pulses represent the equivalent of one coin (coin 1).
NOTE: Enhanced debit mode cannot be deselected.
Control Set-Up Procedures
IMPORTANT: Read all instructions before operating.
The fabric setting buttons along with the digital display are used
to set up the dryer controls.
The display can contain four numbers and/or letters and a
decimal point. These are used to indicate the set-up codes and
related code values available for use in programming the dryer.
How to Use the Buttons to Program the Controls
1. The COTTON/WHITES button is used to adjust the values
associated with set-up codes. Pressing the button will change
the value by increments. Rapid adjustment is possible by
holding down the button.
2. The PERM PRESS button will advance through the set-up
codes. Pressing this button will advance to the next available
set-up code. Holding down the button will automatically
advance through the set-up codes at a rate faster than
one per second.
3. The COLORS/DELICATES button is used to select
or deselect options.
topofftime
=
full cycle length
27