Designated Use; Unpacking The Appliance; Overview Of The Components / Delivery Scope; Installation - Profi Cook PC-UM 1113 Instrucciones De Servicio

Designated Use

This device is used for:
• Mixing of liquids
• Chopping fi rm foodstuffs
• Crushing ice
Do not use for too hard foodstuffs such as nuts or chocolate.
It is intended for the use in private households and similar
applications.
It is only to be used as instructed in this user manual. The
appliance is not intended for commercial use.
Any other use shall be considered as not intended use and
can lead to material damage or even personal injury.
The manufacturer shall not be liable for damages caused by
not intended use.

Unpacking the Appliance

1. Remove the device from its packaging.
2. Remove all packaging materials like foils, fi lling materials,
cable holders, and carton packaging.
3. Check the scope of deliveries for completeness.
NOTE:
There may still be dust or production remains on the
device. We recommend that you clean the device as
described under "Cleaning".

Overview of the Components / Delivery Scope

1 Refi ll opening cap / Measuring cup
2 Mixing vessel lid with refi ll opening
3 Mixing vessel
4 Knife block
5 Locking ring for blade unit
6 Motor housing
7 Setting switch

Installation

Mixing Vessel
1. Place the mixing vessel onto the motor housing. Follow
the symbols on the housing. Position the mixing vessel so
that the handle lies above the symbol.
2. Secure the mixing vessel by turning it clockwise.
NOTE:
The mixer will not operate if assembled incorrectly.
Lid
1. Put the lid on, so that the larger side is located over the
spout. Press the lid fi rmly onto the mixing vessel. It must
seal the mixing vessel completely.
2. Insert the cap into the refi ll opening of the lid. Tighten the
cap by turning it clockwise.
32
PC-UM 1113_IM
NOTE:
The refi ll opening cap can also be used as a measuring cup.

Notes on Use

CAUTION:
The glass may crack if the temperature is too high! Do not
fi ll with liquids above 60°C.
• Fully unwind the mains cable from the bottom of the ap-
pliance.
• Place the device on a fi rm and fl at surface. Position it is
such that it cannot tip over.
• Only switch on the appliance if the mixing vessel is closed
with the lid. The refi ll opening in the lid must also be closed.
• Do not overfi ll the mixing vessel! You can fi ll it to a maxi-
mum of 1.8 litres. Use the scale on the jug.
• Froth requires a large capacity. Reduce quantities of liq-
uids which produce a lot of froth.
• Keep one hand on the lid if you are crushing ice or if there
is a large quantity of ingredients.
• Cut the food to be mixed into small pieces beforehand.
• Use only a scraper made of plastic or rubber to remove
the mixture from the vessel. Do not use metallic objects.
Electric Connection
• Before inserting the power plug into the outlet, check that
the mains voltage to be used matches that of the device.
You can fi nd the required information on the nameplate.
• Connect the device only to a correctly installed safety
socket.
Short-Interval Use
The appliance is suitable for short-interval use of a maximum
of 2 minutes. Allow it to cool for 3 minutes before using it again!
NOTE:
The housing may get hot during operation.
Pulse Mode
Switch to pulse mode by turning the control to the "P" position
and then release it. Use the appliance in this operating mode
for a maximum of 2 minutes. Allow it to cool for 3 minutes
before using it again!
Crushing Ice Cubes
The blades in the mixing vessel are also suitable for crushing
ice cubes.
• Put a maximum of 10 pieces (size approx.
25 x 25 x 25 mm) into the mixing vessel.
• Use pulse operation "P" for 1 - 3 seconds. Repeat the pro-
cess 8 - 12 times.
22.11.16