Página 1
SHINDAIWA OWNER’S/OPERATOR’S MANUAL T350 GRASS TRIMMER INTL Version C350 BRUSHCUTTER INTL, EMC Version T350 C350 Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection WARNING! when operating this unit.
If you have ques- serious bodily injury. operator, you’ll soon discover for your- tions regarding your Shindaiwa power self why Shindaiwa is simply in a class by tool, or if you do not understand some- itself! thing in this manual, your Shindaiwa CAUTION! dealer will be glad to assist you.
FLYING DEBRIS! stance that could affect your ability or judgement. Use only authorized Shindaiwa parts WARNING! and accessories with your Shindaiwa Use Good Judgment trimmer or brushcutter. Do not make modifications to this unit without the...
Página 4
The Properly Equipped Operator Wear hearing protection devices and a broad- Always wear eye protection such as goggles or safety brimmed hat or helmet. glasses to shield against thrown objects. Always wear a harness when operating a unit Wear close-fitting clothing to protect legs and equipped with a blade.
ANSI B175.3. 35002 C350 IMPORTANT! Safety and Operation Information Labels: Make sure all information labels are undam- aged and readable. Immediately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer. Figure 3...
Operating rpm Range .............................5500–8500 rpm (min Transmission Type ....................Automatic centrifugal clutch through bevel gears Fuel/Oil Ratio ......................50:1 with Shindaiwa Premium 2-cycle mixing oil Fuel Tank Capacity, T350 ..............................34 oz./1000 ml Fuel Tank Capacity, C350 ..............................34 oz./1000 ml Carburetion .................................
3. Rotate the outer tube until the gearcase output shaft faces down, away from the spark plug on the powerhead. 4. Tighten both tube clamp screws equally. 5. (T350) Position the throttle assembly with the throttle lever down (away from the spark plug), and tighten both throttle clamp screws securely.
Assembly: Handlebar and Throttle Assembly (C350) 1. Use the 4mm hex wrench to remove Throttle the lower cap retaining screws from Assembly the handlebar bracket. Remove the cap from the bracket. Throttle Cable 2. Position the handlebar on the outer tube forward of the handle position- ing label as shown in Figure 7.
Página 9
WARNING! 2. (T350 only) Fit the two shims and NEVER operate the unit without the the bracket over the outer tube and cutting attachment shield installed loosely install the four socket-head and tightly secured! screws.
Página 10
5. Remove the hex wrench from the (Per ANSI B175.3). When using a gearcase and holder. blade, the unit must also be equipped with a harness or strap. The T350 should now be completely assembled and ready for use as a grass trimmer.
Página 11
Assembly: Install the Blade (C350) NOTE: The C350 is shipped with holder A, the Shaft Bolt safety clip, holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT- Bolt Guard HAND THREAD AND IS REMOVED IN Holder B A CLOCKWISE ROTATION! Safety...
If fuel must be stored longer around the fuel filler cap. an oxygenate! Oxygenated fuels than 30 days and Shindaiwa One oil may cause increased operating 3. Remove the fuel cap, and fill the tank with fuel stabilizer is not used, it should temperatures.
Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, "I" for ON or START and "O" for OFF or STOP. 1. Set the throttle lever to “fast idle” by T350 Throttle Assembly C350 Throttle Assembly performing the following:...
Adjustments may vary because of 35025 Figure 24 altitudes and other factors. See your Idle the engine briefly before stopping authorized Shindaiwa dealer for correct (about 2 minutes), then slide the ignition adjustments. switch to the “O” (Engine OFF) position. See Figure 24.
Shoulder Strap and Harness Using a Grass Trimmer (T350) IMPORTANT! Your Shindaiwa T350 Grass Trimmer Engine Operating Speeds may be equipped with one of several Adjust the shoulder strap or harness Operate at full throttle while cutting Shindaiwa trimmer head models, each so the shoulder pad rests comfortably grass.
A brushcutter’s handlebar helps prevent DO NOT use 2-tooth or NON- injury or damage. the operator from moving forward, or Shindaiwa approved 4-tooth cutting Never use a blade for purposes the unit moving rearward, thus prevent- blades with Shindaiwa brushcutters.
DO NOT use 2-tooth or NON- Shindaiwa approved 4-tooth NOTE: cutting blades on Shindaiwa trim- Using non-standard replacement parts mers or brushcutters. could invalidate your Shindaiwa war- Blades are not interchangeable ranty.
Use only lith- Check for loose or missing screws or ium-base grease such as Shindaiwa components. Make sure the cutting Gearcase Lubricant or equivalent. attachment is securely fastened.
Drain all the fuel from the fuel tank. determine if a spark arrester is required Shindaiwa Tornado™ Blade IMPORTANT! in your area. To sharpen All stored fuels should be stabilized with...
87 or higher, mixed with fuel of the proper grade? Shindaiwa Premium 2-cycle mixing oil at a 50:1 gasoline/oil ratio. Check for clogged fuel filter and/or vent. Replace fuel filter or vent as required. Restart.
Página 21
Head Office: 6-2-11 Ozuka Nishi 11975 S.W. Herman Rd. Part Number 72540-93112 Asaminami-Ku, Hiroshima Tualatin, Oregon 97062 Revision 5/05 731-3167, Japan Telephone: 503 692-3070 Shindaiwa is a registered trademark Telephone: 81-82-849-2220 Fax: 503 692-6696 of Shindaiwa, Inc. Fax: 81-82-849-2481 www.shindaiwa.com...