Magura HS 11 Manual De Instrucciones página 21

Ocultar thumbs Ver también para HS 11:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 64
installing brake cylinders
Important.– see.
,.page.20!
general
Screw.the.quick.release.screw.
(
1
)
.
seen.from.above).–.by.10–12.turns.at.first.
Push.the.mounting.plate.onto.the.cantilever.socket..
)
.
The.spacers.
.are.only.required.if.the.mounting.plate.or.adapter.are.in.
(
2
)
Î
Î
contact.with.the.fork.–.max..1.shim.per.cantilever.socket,.flattened.
side.uppermost!
The.lettering."EVO2".must.be.legible.from.the.front.(as.seen.from.above).
Î
Î
Place.the.left.brake.cylinder.(2.connecting.lines).on.the.left.cantilever.
)
.
socket.(as.seen.from.above).and.mounting.plate.–.secure.with.a.washer.
[
]
and.socket.screw.
(
3
)
.
B2
.
Screw.in.the.adapter.screw.
(
4
)
.and.socket.screw.
)
.
cylinder.and.adapter.can.just.still.be.moved.
Place.the.right.brake.cylinder.with.open.quick.release.skewer.
)
.
onto.the.right.cantilever.socket/quick.release.screw.and.mounting.
plate.–.set.the.quick.release.lever.to.the.up.position.(CLOSED).
Screw.in.the.adapter.screw.
.and.quick.release.screw.
(
4
)
)
.
brake.cylinder.and.adapter.can.just.still.be.moved.
adjusting brake cylinders
Install.the.wheel.into.the.dropouts.as.far.as.it.will.go.–.preferably.with­
)
.
out.tires.
Make.sure.that.the.rim.is.located.exactly.in.the.middle.between.the.
)
.
fork.blades.or.seat.stays.of.the.rear.triangle.–.centre.the.wheel.if.
. n ecessary.
restricted adjustment capability.
The.exclusive.purpose.of.the.pressure.point.adjusting.screw.(TPA).is.to.
compensate.for.brake.pad.wear..Do.not.use.the.TPA.for.the.basic.setting.
of.the.brake.cylinders.–.the.brake.shoes.must.be.fully.advanced..Other­
wise.there.might.not.be.sufficient.adjustment.travel.available.later.on.
.into.the.right.cantilever.socket.(as.
)
[
]
B1
.
[
]
B1
(
3
)
.until.the.brake.
.(OPEN).
(
5
)
[
]
B3
.until.the.
(
1
)
Make.sure.that.the.pressure.point.adjusting.screws.(TPA).
)
.
[
screwed.to.the.stop.(­).
Brake.shoes.are.fully.advanced.
Î
Î
Push.the.brake.cylinders.inwards.until.the.brake.pads.are.in.full,.flat.
)
.
contact.with.the.brake.track.area..
Move.the.adapter.up.or.down.if.necessary.until.the.top.edges.of.the.
)
.
brake.pads.are.1–2.mm.below.the.edge.of.the.rim.
Brake.pads.are.in.full,.flat.contact.with.the.brake.track.area.
Î
Î
Brake.pads.are.aligned.exactly.parallel.with.the.rim.
Î
Î
Brake.pads.cannot.come.into.contact.with.the.tires.
Î
Î
Adapters.are.at.the.same.height.
Î
Î
Pull.the.brake.lever.carefully.
)
.
Brake.shoes.retract.
Î
Î
Brake.cylinders.are.pushed.outwards.
Î
Î
carefully.pull.the.brake.lever.and.release.until.a.gap.of.1–1.5.mm.is.
)
.
produced.on.one.side.between.the.brake.pad.and.brake.track.area..
.
Then,.on.this.side:.tighten.the.adapter.screw.
)
.
a.tightening.torque.of.max. 6 n·m (53 lbf·in).
release.skewer.to.the.definitive.pressure.– see.
,.page.22.
skewer
carefully.pull.the.brake.lever.and.release.until.a.gap.of.1–1.5.mm.is.
)
.
also.produced.on.the.other.side.between.the.brake.pad.and.brake.track.
[
]
area..
B6
Then,.on.this.side:.tighten.the.adapter.screw.
)
.
a.tightening.torque.of.max. 6 n·m (53 lbf·in).
release.skewer.to.the.definitive.pressure.– see.
,.page.22.
skewer
i
nstallatiOn
(
]
.
B4
[
]
B5
(
)
.and.socket.screw.
4
[
]
B7
.or.set.the.quick.
adjusting the quick release
.and.socket.screw.
(
4
)
[
]
.or.set.the.quick.
B7
adjusting the quick release
6
)
.are.un­
[
]
B6
(
)
.to.
3
.to.
(
3
)
21

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Hs 33

Tabla de contenido