Installing.the.brake.booster. . 22 Montage.du.arceau.rigid - Magura HS 11 Manual De Instrucciones

i
nstallatiOn
adjusting the quick release skewer
Operate.the.quick.release.lever.–.open/close.
) .
If.the.quick.release.lever.can.be.closed.too.easily,.the.quick.release.
L L
[ ]
screw. ( 1 ) .must.be.adjusted. g1 :
Move.the.quick.release.lever.up.(CLOSED).
) .
Screw.in.the.quick.release.screw.by.¼.turn.clockwise.
) .
Operate.the.quick.release.lever.–.open/close.
) .
Repeat.the.procedure.if.necessary.
) .
installing the brake booster
Unscrew.the.right.adapter.screw.
) .
Push.the.brake.booster.onto.the.left.adapter.screw.
) .
Secure.the.brake.booster.with.the.adapter.screw.
) .
Tighten.the.right.adapter.screw..
) .
[ ]
max. 6 nm (53 lbf·in). .
c1
shortening brake hose
Important.– see. ,.page.20!
general
Push.the.double.hose.cover. ( 1 ) .upwards.
) .
Cut.off.the.brake.hose.approx..12.mm.before.the.end.of.the.hose.–.use.
) .
a.MAGURA.hose.cutter.if.required.
Twist.the.barbed.fitting. ( ) .out.of.the.brake.cylinder.with.the.remains.of.
2
) .
the.hose.
The.cut­off.barbed.fitting.cannot.be.reused!
Î Î
Hold.the.end.of.the.brake.hose.to.the.brake.cylinder
) .
unusable brake hose – because it is too short.
Calculate.the.insertion.depth.(~5.mm).of.the.brake.hose.in.the.brake.
Î –
[ ]
cylinder .
D3
Mark.the.cut.on.the.brake.hose.
) .
Place.the.brake.hose.on.a.solid.surface.(wood,.plastic,.etc.).and.cut.at.
) .
right.angles.with.a.sharp.blade.–.if.required.use.the.MAGURA.hose.
cutter.
22
( 4 ) .(as.seen.from.above).
( 4 ) .and.washer.
( 4 ) .with.a.tightening.torque.of.
[ ]
D1 .
[ ]
D3 .
Place.the.sleeve.nut. ( 4 ) .and.olive.
) .
Insert.the.brake.hose.into.the.brake.cylinder.to.the.stop.and.hold.in.
) .
position.
Screw.the.sleeve.nut. ( 1 ) .into.the.brake.cylinder.and.tighten.to.a.tighten­
) .
[
ing.torque.of.4 n·m (35 lbf·in)
B1
Remove.any.oil.residues.thoroughly.
) .
Pull.and.hold.brake.lever.
) .
Make.sure.that.all.connections.are.tight.
) .
Push.the.hose.cover. .downwards.
( 1 )
) .
adjusting the brake levers
You.can.adjust.the.position.(grip.width).of.the.brake.levers.of.your.
L L
MAGURA.HS.according.to.your.requirements.
This.adjustment.does.not.have.any.effect.on.the.pressure.point.of.the.
brake!
Screw.the.adjusting.screw. .out.
( 1 )
) .
Brake.lever.moves.closer.to.the.handlebar.
Î Î
Screw.the.adjusting.screw.in. +
( )
) .
Brake.lever.moves.further.away.from.the.handlebar.
Î Î
All.installation.work.is.complete.–.the.brake.is.ready.for.use.
Î
Î
[ ]
( 5 ) .on.the.brake.hose D4 .
]
.
[ ]
.
e1
­ .
( )
.