S&P TH-ECOWATT Serie Manual De Instrucciones página 9

ENGLISH
Instructions Manual
Thank you for placing your confidence in S&P by buying this
product. It has been manufactured following current technical
safety regulations and in compliance with EC standard.
Please read this instruction booklet carefully before installing
or starting up the product. It contains important information on
personal and user safety measures to be followed while
installing, using and carrying out maintenance work on the
equipment. Once the product has been installed, please hand
in this booklet to the end user.
Check that the apparatus is in perfect condition while
unpacking. Any fault or damage caused in origin is covered by
the S&P guarantee. Please make sure that the apparatus
coincides with the product you have ordered and that the
details on the instructions plate fulfil your requirements.
Transport and manipulation.
- The packaging used for this apparatus has been designed to
support normal transporting conditions. The apparatus must
always be transported in its original packaging as not doing
so could deform or damage the product.
- The product should be stored in a dry place in its original
packaging, protected from dust and dirt until it is installed in
its final location. Do not accept delivery if the apparatus is not
in its original packaging or shows clear signs of having been
manipulated in any way.
- Do not place heavy weights on the packed product and avoid
knocking or dropping it.
- When manipulating heavy products, adequate elevating
machinery should be used to avoid harming people or
damaging the product itself.
- Never lift a product by pulling it by the wires or terminal
casing. Likewise, no pressure should be applied on the
propeller, turbine or safety grid while manipulating the
product.
Important information for the safety of installers and users.
- Installation must only be carried out by qualified persons.
- Make sure that the installation complies with each country's
current mechanical and electrical norms.
- Once ready to use, the apparatus must fulfil the following
standards:
 Standard for Low Pressure Instalments 2006/95/CE
 Machinery Standard 2006/42/CE
 Standard for
2004/108/CE.
- Ventilators installed in high risk areas (1) that are accessible
to users must be adequately protected in order to comply
with the Standards.
- Any area in or around a machine, where the safety of people
may be at risk.
- Ventilators, or apparatus that include them, have been
designed to move the air in the area stipulated on their
characteristics plate.
- This apparatus must not be used in explosive or corrosive
atmospheres.
- If a machine is needed for working in the previously stated
conditions, consult the S&P Technical Service.
- If the apparatus is going to be used in atmospheres with over
95% relative humidity, consult the S&P Technical Service
first.
- If a ventilator is going to be installed to extract air from
premises where a boiler or other combustion apparatus are
installed, make sure that the building has sufficient air
intakes to assure adequate combustion.
Safety during installation.
- Make sure there are no loose elements near the ventilator. If
it is going to be installed in a duct, check that it is clean of
any elements.
- When installing an apparatus, make sure that all the fittings
are in place and that the structure which supports it is
resistant enough to bear its weight at full functioning power.
Electromagnetic Compatibility
- Before manipulating the apparatus, make sure the mains
supply is disconnected, even if the machine is switched off.
- Check that the mains supply voltage and frequency values
coincide with the stipulations on the characteristics plate.
- Please follow the connections diagram for the electrical
connections.
- If an earth connection is necessary, check that it correctly
connected and that adequate thermal and overloading
protection has been connected and adjusted to the
corresponding limits.
- If a ventilator is installed in a duct, the duct must be
exclusively used for the purpose of the ventilation system.
Starting up.
Before starting up the machine, make sure that:
- The apparatus is well secured and the electrical connections
have been carried out correctly.
- The safety devices have been adequately connected.
- No loose material or fitting remains surrounds the ventilator.
If the ventilator has been mounted in a duct, make sure it is
clear of loose material.
- The earth fittings are adequately connected.
- The electrical safety devices are correctly connected,
adequately adjusted and ready for use.
- The wire and electrical connections inputs are correctly
sealed and water-tight.
When starting up the machine, make sure that:
- The propeller turns in the correct direction.
- There are no abnormal vibrations.
- If any of the electrical safety devices blow, the apparatus
must be quickly disconnected from the mains supply. The
whole installation should be carefully checked before trying
to start up the machine again.
Maintenance.
- Before servicing the ventilator, make sure it is disconnected
from the mains supply even if it has previously been switched
off. Prevent the possibility of anyone else connecting it while
it is being serviced.
- The apparatus must
inspections should be carried out bearing in mind the
machine's working conditions, in order to avoid dirt or dust
accumulating on the propeller, turbine, motor or grids. This
could be dangerous and perceptibly shorten the unit working
life.
- Whilst cleaning, great care should be taken not to tamper
with the propeller or turbine.
- All maintenance and repair work should be carried out in
strict compliance with each country's current safety
regulations.
Recycling.
In accordance with EEC Standards and our responsibility for
future generations, we are obliged to recycle all the materials
we can. Therefore, please deposit all waste material and
packaging in their corresponding recycling containers and
hand in the replaced units to the nearest handler of this type of
waste product.
For any question concerning S&P products, please contact
your local distributor. For its location, you can visit the web
page www.solerpalau.com
be regularly inspected. These